Panasonic NV-SJ260 Series Operating Instructions Manual page 12

If you are connecting your VCR to a TV using Method 2,
follow the operations explained below.
To be able to watch the VCR picture on the TV, RF
connection requires the video playback channel to be set on
the TV.
01 Switch the TV on.
02 Select an unoccupied programme position (which is not
tuned to a TV station).
If you are using a Panasonic TV, select programme
position "0".
03 Set the VCR/TV switch
04 Press the VCR-ON/OFF button
05 Press the MENU button
more than 5 seconds.
The number of the RF output
channel appears on the VCR
display.
The initial setting is channel 36.
06 Tune your TV until the test pattern shown on the right
appears on the TV screen.
Now, the setting of the RF output
channel is complete.
≥ As the tuning method differs
depending on the TV you are
using, refer to your TV's
operating instructions for
details about tuning.
07 Press the OK button
The Country setting menu
appears on the TV screen.
08 Press the Cursor buttons
(3421) to select the
country where you are using
the VCR.
09 Press the OK button
the VCR's Auto Setup
automatically starts and tunes
all available TV stations and
also sets the clock. This
takes about 5 minutes.
≥ If you select "Schweiz",
"Suisse" or "Svizzera" on the
Country setting menu, see
page 11.
10 When the indication shown
on the right appears on the
VCR display, the Auto Setup
is complete.
To Cancel the Auto Setup Before It Has Finished
√
Press the EXIT button
12
to "VCR".
to switch the VCR on.
VCR display
for
Indication when the RF output
channel is 36 (example)
On Screen Display
Panasonic
VCR
Ch:36
Indication of the test pattern
.
Country
Deutschland
België
Österreich
Belgique
Portugal
Belgien
Danmark Suomi
España Sverige
France Schweiz
Italia Suisse
Svizzera
Nederland
others
Norge
Menu for Country setting
and
Auto-Setup
Auto-Setup
in progress,
please wait.
Ch 21
Indication during Auto Setup
CVC
Programme Indication when the
position current time is 16:45
.
When the clock setting menu appears after Auto Setup has
finished:
See page 11.
To Confirm that the TV Stations Have Been
Tuned Correctly by the Auto Setup
Function
See page 11.
If the Picture on the TV's Video Playback
Channel Is Distorted
If, after setup, you select the video playback channel
on the TV and view a TV programme on a programme
position selected on the VCR, some interference may occur
in certain cases. If this happens, you can minimise the
distortion by changing the RF output channel on the VCR to
another number. Follow the operations below.
1 Set the VCR/TV switch
2 Press the MENU button
The number of the RF output channel appears on the
VCR display.
The initial setting is
channel 36.
3 Press the numeric buttons
channel.
Enter a channel number which differs by 2 or 3 from the
one initially set number. For example, as the original
number is 36, enter 39.
4 Press the OK button
Note When You Have Changed the RF Output Channel:
After changing the RF output channel to a different number,
be sure to retune your TV to the VCR's new RF output
channel. (For details about tuning, refer to your TV's
operating instructions.)
1 Press the MENU button
2 When the test pattern shown on
the right appears sharp and
clear on the TV screen, the
tuning is complete.
3 Press the EXIT button
to "VCR".
for more than 5 seconds.
Indication when the RF output
channel is 36 (example)
to change the RF output
Indication after changing the RF
output channel to 39 (example)
to conclude the setting.
for more than 5 seconds.
Panasonic
VCR
Ch:39
Test pattern indication
to exit the On Screen Display.