Panasonic AJ-SD755 Operating Instructions Manual page 66

Error messages
Error messages
ODescription
Display
OVTR operation and corrective action
E-20 If condensation is detected, the error number
flashes and the unit transfers to eject mode. The
DEW drum rotates after the cassette is ejected to
eliminate the condensation.
Once the unit is released from condensation
status, the error message display is cleared and
the VTR is able to be used.
OIf condensation is detected in the eject mode,
the drum starts rotating as soon as it is
detected.
OIf condensation is detected when the cassette
has been inserted, the drum rotation is
stopped, and after the tape is ejected, the
drum starts rotating.
VTR: EJECT
OLeave the power on and wait.
E-29 The unit switches to eject mode and if the
cassette fails to move up within 6 seconds, this
FRONT LOAD error number flashes on the display.
MOTOR OIf the cassette does not move down inside the
machine even when 6 seconds have elapsed
since the cassette was inserted, the VTR is
transferred to the eject mode.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-31 If the unloading operation is not completed
within 6 seconds, this error number flashes on
LOADING the display.
MOTOR OWhen the loading operation is not completed
within 6 seconds, the VTR is transferred to the
eject (unloading) mode.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-35 If there is no response from the servo
microcomputer for 1 second or more, this error
SERVO number flashes on the display.
CONTROL VTR: STOP
ERROR OSet the POWER switch to OFF and then to
ON again.
E-37 If 10 seconds or more elapses and the servo
microcomputer has not followed orders issued
SERVO COMM by the system control microcomputer, this error
ERROR number flashes on the display.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-38 If automatic adjustment of the reel and capstan
rotation in eject status was not performed
SERVO FG correctly when the power was turned on, this
ERROR error number flashes on the display.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
66
ODescription
Display
OVTR operation and corrective action
E-51 If the take-up reel rotates without engaging for a
specific period of time during the start or end
FRONT LOAD processing operation while loading is underway
ERROR (half position), this error number flashes on the
display.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-52 If the take-up reel fails to take up the tape while
the tape is traveling in the state where the total
W-UP REEL amount of the tape has not yet been detected
NOT ROTA after the cassette was inserted, this error
number flashes on the display.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-53 If there is an abnormally large discrepancy
between the amount of tape taken up by the
WINDUP take-up reel and the amount of tape supplied by
ERROR the supply reel while the tape is traveling after
the total amount of the tape begins to be
detected, this error number flashes on the
display.
VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-55 If the tape has not been taken up during
unloading, this error number flashes on the
UNLOAD display.
ERROR VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-57 If the start or end processing operation is not
completed, this error number flashes on the
S-FF/REW display.
TIMEOVER VTR: STOP
OSet the POWER switch to OFF and then to
ON again.
E-59 If the cylinder motor speed is abnormally low,
this error number flashes on the display.
DRUM ROTA VTR: STOP
TOO SLOW OSet the POWER switch to OFF and then to
ON again.
E-60 If the cylinder motor speed is abnormally high,
this error number flashes on the display.
DRUM ROTA VTR: STOP
TOO FAST OSet the POWER switch to OFF and then to
ON again.
E-61 If the capstan motor speed is abnormally low,
the error number flashes on the display.
CAP ROTA VTR: STOP
TOO SLOW OSet the POWER switch to OFF and then to
ON again.