Operating Hints - Grundig STR 600 AP Service Manual

Operating Hints

This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in the
relevant spare parts list.
3
1 2
TIMER
POWER TIMER
Front Side/The Receiver's Controls
Switches the receiver in stand-by and on
again. No disconnection from the mains!
Panda Logo*
The yellow indication is lit if a Timer is
"active" (the preprogrammed timer time is
elapsing).
The red stand-by pilot lamp is lit if the
receiver is in stand-by.
The receiver's display (see description in
next column).
¶ This key is protected against inadvertent
actuation. Press it for more than 2
seconds to call up the menu for adjusting
the aeriel motor.
¶ Exit menu (without saving).
E XIT
› › – Select programme positions step-by-
P + P–
step (long pressure: scrolling).
– Switch on from stand-by with last
selected programme position (last sta-
tion memory).
– When in a menu: select a line.
F E – Change volume. If the volume is very
low, "Vol min" appears on the picture
screen.
– When in a menu: change value
q – Indication of the station name and of the
satellite on the picture screen.
– When in a menu: save setting.
Ideal matching of GRUNDIG video recor-
der and GRUNDIG SAT receiver. Only the
video recorder needs programming.
Recording control then takes place auto-
matically via data transmission from the
video recorder to the SAT receiver using a
control cable. For more information, see
page 27.
* Panda/Wegener Communications Inc.
Award for supreme sound quality.
4
STR 600 AP
P+
RADIO
OK
EXIT
P-
9 9
9 9
The Receiver's Display
9 9
3-digit programme position indication.
Ost
Indicates the aerial run.
ARD
8-digit display.
– On normal operation, it indicates the station name
ϒ
of the selected programme position.
W
– If a menu is displayed, it indicates " Menue ".
R R
– If the aerial is running, it indicates, for example,
" O " and the position reached, for
E E
O O
example " 19 «.
I I
M M
" " " "
1 2 3 4
I I
Indicates which internal timer is programmed.
D D
T T
A A
Is lit if at least one timer is programmed.
R R
Is lit if a radio programme position is selected.
MEGA-
TV LOGIC
SAT
INPUT-SAT
R
950-2150 MHz
EURO AV TV EURO AV DECODER
14/18 V 450 mA
AUDIO OUT
L
Rear side Pin Assignment
INPUT SAT Connector for satellite aerial. 1 2 3 4 5 6 7 8 9 10
(10-pin connector):
Output for terrestrial aerial and
SAT-UHF output. The plug can be removed, the indications (1 ... 10)
can be seen from the top.
Input for terrestrial aerials
(VHF/UHF). Pin
11
MEGALOGIC Connector for remote control
by various GRUNDIG video
SAT
recorders (see chapter "SAT
12
Recording Control via a
GRUNDIG Video Recorder
(MEGALOGIC SAT" on page 27)
13
and the "Datalink" function (see
14
page 30).
AUDIO Audio connectors for the con-
15
OUT R/L nection of hifi equipment
R: right, L: left
16
EURO-AV EURO-AV socket (output)
TV for TV set with RGB signal loop-
17
through from decoder socket.
18
EURO-AV EURO-AV socket (input/output)
for PAL/MAC decoder or a second
DECODER
19
video recorder (see chapter
"Decoder Socket/Switching Vol-
10
tage, page 21).
EURO-AV EURO-AV socket (input/output)
for video recorder.
VCR
* Maximum nominal current consumption 1.5 A,
Mains connector for plug-in
220-240 V
brief peak values of 2.5 A are possible.
50-60 Hz mains cable. The unit is only dis-
connected from the mains when
the mains plug is removed!
10 9 8 7 6 5 4 3 2 1
220-240 V ~
EURO AV VCR
50-60 Hz
Designation Connection
0/12 V/ 0,1 A Switching voltage output for
LNB switching, relay, or simi-
lar.
AGC Field strength measuring out-
put for exact aerial positio-
ning.
GND Ground
+5 V/ 0,2 A Output for motor polarizer or
actuator.
– I
– I – POL. Control impulse voltage (out-
put) to motor polarizer.
MAGN. Current supply for magnetic
polarizer ±70 mA/max. ±12 V
GND Ground
M2 Operating voltage for 36 V
rotating motor (positive on
east run)*
M1 Operating voltage for 36 V*
rotating motor
– I
– I Control impulse voltage (input
–
from rotating motor)