Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Technische Alternative RAS-PLUS
Summary of Contents for Technische Alternative RAS-PLUS
-
Page 1: Installation Instructions
RAS-PLUS (/F) Version 1.10 EN Room sensor with remote display RAS-PLUS = Room sensor with RAS-PLUS/F = Room sensor with temperature measurement and remote temperature and humidity measure- display ment and remote display Operation Programming Installation instructions... -
Page 3: Table Of Contents
Table of Contents Function description ..................4 Programming manual ..................5 Menu – general overviews ....................6 Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611 ........6 Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-3 (from version 8.3), UVR63 (from version 1.5) .................... -
Page 4: Function Description
The RAS-PLUS transmits the room temperature, relative room humidity (only RAS-PLUS/F) and the dew point (only RAS-PLUS/F), the operating mode and the correction value for the nominal value (+/- 5K) to the controller via the bidirectional data link (DL-bus). Using the DL- bus it is also possible to display controller sensor values, output states, heat quantity counter outputs and network inputs at the RAS-PLUS (remote display). -
Page 5: Programming Manual
Access to the programming level is only possible from the "Standby" position (extreme left) of the slider switch. RAS-PLUS can be configured using the key and set up to display further values. The following symbols are used in the menu descriptions to differentiate between long and... -
Page 6: Menu - General Overviews
Menu – general overviews The displayed menu options are matched to the respective controller types: Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611 In the menu section "CONFIG" gen- eral sensor settings are adjusted. The selection of the values and sym- bols to be displayed takes place in the menu section "VALUES". -
Page 7: Menu Overview For Esr21 (From Version 5.0) And Esr31, Uvr61-3 (From Version 8.3), Uvr63 (From Version 1.5)
Menu overview for ESR21 (from version 5.0) and ESR31, UVR61- 3 (from version 8.3), UVR63 (from version 1.5) In the menu section "CONFIG" gen- eral sensor settings are adjusted. The selection of the values and sym- bols to be displayed takes place in the menu section "VALUES". -
Page 8: Menu Overview For All Other Controllers
Menu overview for all other controllers In the menu section "CONFIG" gen- eral sensor settings are adjusted. The selection of the values and sym- bols to be displayed takes place in the menu section "VALUES". The menu option "POWER" (heat quantity counter) is only displayed with those controllers that have this function. -
Page 9: Menu Config
Switchover between German (DE) and English (EN) Factory setting: DE To activate the language selection the RAS-PLUS must be initialised by scrolling forward in the display level. Time interval for continuing display TIME N Entry 0 = no automatic forwarding between... -
Page 10: Time Before Jumping Back To The 1St Display Time B
Time before jumping back to the 1st display TIME B Entry = 0 There is no jump back of the dis- play to the 1st value. Factory setting: 0 After a long key press "0" flashes Selection of the desired time by a short key press. -
Page 11: Address In The Dl-Bus Network Dl Adr
Amongst those controllers that have no bidirectional data link (e.g. HZR65), i.e. amongst those for which the RAS-PLUS can only be used as a remote display, this menu option is still displayed but has no effective function and must therefore not be observed. -
Page 12: Index Specification
Measured room temperature (no offset values of the +/- adjustment and the slider switch (e.g. for the controller UVR61-3) Relative room humidity (only type RAS-PLUS /F) Dew point temperature (only type-RAS PLUS /F) Fixed value 20°C with offset values of the +/- adjustment and the slider switch... -
Page 13: Entry Of An Offset Value For Sensor Correction Offset
Amongst those controllers that have no bidirectional data link (e.g. HZR65), i.e. amongst those for which the RAS-PLUS can only be used as a remote display, this menu option is still displayed but has no effective function and must therefore not be observed. -
Page 14: Display Of Operating Mode Symbols Symb
Display of operating mode symbols SYMB In this menu, you can hide the symbols for the operating mode. With symbols Without symbols Press and hold the button for a long time to select the required display. -
Page 15: Menu Values
Menu VALUES This is where the display is selected: Sensor values SENSOR Output statuses OUTPUT Speed stages SPEED (only UVR16x2, RSM610, CAN-I/O45 and UVR 1611) Heat quantity counter POWER (only for controllers with a heat quantity counter) ... -
Page 16: Menu Output Statuses Output
Menu output statuses OUTPUT Access the menu by a long key press. Selection by a long key press on the rele- vant output. The selection is indicated by a star. Depending on the controller type, up to 14 output statuses can be displayed. Analogue outputs 15 and 16 of controllers UVR16x2 and UVR1611 cannot be dis- played. -
Page 17: Menu Speed Stages Speed (Only Uvr1611)
Menu speed stages SPEED (only UVR1611) Access the menu by a long key press. Selection by a long key press on the rele- vant output. The selection is indicated by a star. The speed of this output is displayed after all the other displays have been dis- played. -
Page 18: Menu Heat Quantity Counter Power
Menu heat quantity counter POWER This menu option is only displayed for controllers with a heat quantity counter. Access the menu by a long key press. Selection through a long key press of the value in question of the relevant heat quan- tity counter The selection is indicated by a star. -
Page 19: Menu External Sensors Netw (Only Esr21 (From Version 5.0), Esr31, Uvr61-3 (From Version 8.3), Uvr63 (From Version 1.5))
Menu external sensors NETW (only ESR21 (from version 5.0), ESR31, UVR61-3 (from version 8.3), UVR63 (from version 1.5)) This selection is only possible for the above listed controllers, as only these controllers can display external sensors across the data link. Access the menu by a long key press. -
Page 20: Menu Analog Can Network Inputs Analnw (Only Uvr1611)
Menu analog CAN network inputs ANALNW (only UVR1611) This selection is only possible for the controller UVR1611 as other controllers do not have any CAN network. For output 14, the query must be set to " ". NETW.IP.=>DL.: Access the menu by a long key press. Selection through a long key press by the relevant analog network input. -
Page 21: Menu Digital Can Network Inputs Diginw (Only Uvr1611)
Menu digital CAN network inputs DIGINW (only UVR1611) This selection is only possible for the controller UVR1611 as other controllers do not have any CAN network. For output 14, the query must be set to " ". NETW.IP.=>DL.: Access the menu by a long key press. Selection by a long key press by the rele- vant digital network input. -
Page 22: Menu Symbol Allocation Symb
Menu symbol allocation SYMB This menu is for allocation of a symbol (or several symbols) to the display values. However each symbol can only be allocated once to a display value. The following symbols can be allocated: Example: The symbol "Burner" should be allocated to the output O5: Access the menu by a long key press. - Page 23 A long key press confirms the allocation of the "Burner" symbol to the output O5. Flashing of the symbol stops. Scroll forward to the next symbol to be allocated or ..quit the menu by scrolling forward to "EXIT" If the symbol is allocated to an Output or a Digital CAN network input (UVR1611), then it is shown in each display view for as long as the output or the digital network input is set to "ON".
-
Page 24: Deleting Or Changing A Symbol Allocation
Deleting or changing a symbol allocation: Example: Delete or change the "Burner" symbol allocation to output O5: Access the menu by a long key press. By scrolling forwards with short key presses, the desired "burn- er" symbol appears in the display. A long key press causes the allocation to be cleared. -
Page 25: Reset To Factory Setting
Reset to factory setting To reset the sensor RAS-PLUS to the factory setting, the key must be pressed during inser- tion of the data link into the sensor: The "RESET" display appears briefly Then the menu language is selected (DE =... -
Page 26: Operation
Current room temperature in °C and operating mode symbol Current relative room humidity in % (only RAS-PLUS/F) and operating mode symbol Set value adjustment (only when using the room sensor): Using a ro- tary knob, the room set temperature at the controller can be changed by +/- 5.0K. -
Page 27: Use As A Remote Control
If the installation location of the room sensor is unsuitable as a reference room, the room sensor RAS-PLUS can also be used merely as a remote control, in that Index 5 is used as the measured value. In this way a fixed value of 20°C with offset values of the +/- setting and the slider switch are forwarded to the controller. - Page 28 Legal notice These assembly and operating instructions are protected by copyright. Use outside the copyright requires the consent of the company Technische Alternative elektronische Steuerungsgerätegesellschaft m. b. H.. This applies in particular to reproductions, translations and electronic media.
Need help?
Do you have a question about the RAS-PLUS and is the answer not in the manual?
Questions and answers