Mitsubishi VL-100U5-E Installation Manual
Mitsubishi VL-100U5-E Installation Manual

Mitsubishi VL-100U5-E Installation Manual

Lossnay ventilator
Hide thumbs Also See for VL-100U5-E:

Advertisement

Quick Links

1305875HF7701
Mitsubishi Lossnay Ventilator
MODEL:
(pull cord Type)
VL-100U
-E
5
(wall switch Type)
VL-100EU
-E
5
Installation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VL-100U5-E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mitsubishi VL-100U5-E

  • Page 1 1305875HF7701 Mitsubishi Lossnay Ventilator MODEL: (pull cord Type) VL-100U (wall switch Type) VL-100EU Installation Manual...
  • Page 2: Table Of Contents

    Mitsubishi Lossnay Ventilator MODEL: VL-100U (pull cord type) VL-100EU (wall switch type) Installation Manual For Dealer and Contractor Please ensure that the separate “Operating Instructions” Contents Page are handed over to the customer. Please ensure that it is ......delivered to the customer.
  • Page 3: Dimensional Outline Drawing

    - Electrical work must be done by - Attach the unit so that the air an electrical contractor (a licensed supply/exhaust pipes slope electrician) in accordance with downward toward outdoors. - Rainwater entering the unit could the technical standards of the equipment and local regulations to ensure safety.
  • Page 4 Mounting hole 36 – ø6 Require to be secured Mounting plate Air exhaust hole Power and connection cable pullout area (min.) (Adjustable) (Adjustable) (max.) Air intake hole (min.) (min.) List of included parts Before installation Pipe mounting plates (2) Remove the two screws securing the main unit to remove the mounting plate.
  • Page 5: Mounting Instructions

    Mounting instructions Wall-hole construction 3. Drill the wall holes. Make sure to allow the required clearances (at Wall plate, as shown in the drawing below. hole 5° Wall hole At least Inside Outside 64 mm At least Note 83 mm At least Make the holes so they slope down as they 83 mm...
  • Page 6: Cutting Air Supply/Exhaust Pipes

    Cutting air supply/exhaust pipes Note Check that each air supply/exhaust pipe A catches on all four prongs of its pipe mounting plate. (If a prong has not caught, the pipe will press against the back of the Lossnay unit and the shutter may not Cut on this side operate properly.) Cut perpendicular to the...
  • Page 7: Attaching Air Supply/Exhaust Pipes

    Attaching air supply/exhaust pipes Attaching the main unit For VL-100U attached to the pipe mounting plates, into the wall holes. 2) Press the main unit into the wall and secure it with the two screws provided. At this time, operate properly.) Air supply side Pipe mounting plate Exhaust side...
  • Page 8 Note Operation requires a control switch. Have a control switch ready and Be sure not to misplace the removed terminal block covers and screw. connect the wiring shown in bold on the connection diagram below. 4) Pull the power and connection cables through enter the room at the power/connection cable power and connection cables and screw the ends in place on the terminal block.
  • Page 9: Outdoor Construction

    Outdoor construction covers. Fill in any gaps between the air supply/exhaust Caulking caulking. Caulking Weather covers Air supply/exhaust pipes Note to enter. 2. Installing the weather covers the air supply/exhaust pipes. mounting plates are at the top.) 3) Attach the weather covers with the mounting screws.
  • Page 10: Test Run

    Checks after mounting Check items Checked? Is the main unit mounting strong enough? Is the main unit attached securely? Installation Is the panel securely closed? Close the panel. Caulk. exhaust pipe should be caulked (Failure to caulk will allow rainwater outside, as should the outdoor hood.) Are you using the rated voltage? operation...

This manual is also suitable for:

Vl-100eu5-e

Table of Contents