Table of Contents
Advertisement
SPECIAL FUNCTIONS
SPECIAL FUNCTIONS
A
.
LARM AUTOMATIC ARMING
To obtain this function, connect the YELLOW-GREEN wire to earth.
automatically arm 30 sec, after the engine switching OFF and the door opening.
S
-
ELF
LEARNING OF AN ELECTRONIC KEY CODE
Close the vehicle's doors and disarm the alarm system. Turn the ignition key to ON and within
10 seconds put the electronic key to learn in the socket. The LED switches on for one second.
It is possible to learn a maximum number of 3 keys.
Note: if you put a learned key in the socket this will not annul the other memorised keys;
otherwise, if you put a new key in the socket the first memorised key will be annulled.
G
(
).
ARAGE POSITION
ONLY US MODELS
With this function it is possible to leave the vehicle in the servicing or in the washing centres without
leaving the original transmitter or the electronic key to the staff. To obtain this function, connect the
yellow-green wire to earth.
G
.
ACTIVATION OF THE
ARAGE POSITION
1.
Disarm the alarm, turn the ignition key to ON and open one door.
2.
Turn the ignition key to ON and within 15 sec. put the electronic key in the socket. 2
pulses of the LED signal the activation of the function.
Note: put the key in the socket within the 15 seconds otherwise the procedure will
automatically annul.
3. Turn the ignition key to OFF position.
In this condition the engine of the vehicle can be switched on for 20 times without triggering
the alarm. The working of the GARAGE position is signalled through the fast flashing of the
LED if the ignition key is in ON position for more than 10 seconds.
B
LINKER EXCLUSION WHI LE ALARM ARMING
This function is necessary on vehicles with original flashing of the direction indicator lights
while opening and closing the door.
B
.
LINKER EXCLUSION ACTIVATION
Before supplying the alarm unit, turn the ignition key to ON position.
Supply the alarm system and turn the ignition key to OFF.
LED'
S MEMORY
While alarm disarmed it is possible to verify if an alarm condition has occurred and to
determine the cause following the LED flashing.
LED signalling
¬l¬
¬¬l¬¬
¬¬¬l¬¬¬
¬¬¬¬l¬¬¬¬
l LED OFF (2 sec.) ¬ LED ON (1 sec.)
The inhibit time is 30 sec. for each alarm triggering. Turn the ignition key to ON to stop the
LED flashing.
(US
)
MODELS
/
DISARMING
Alarm triggering
Internal sensors (only 7024US)
Doors pin switches
Ignition live
External sensors(Green-Black wire)
Power supply
The alarm will
Max. current absorption
Working temperature
Contact capacity horn control
Contact capacity visualising signals
Contact capacity engine immobilisation
Alarm period
Max. current –positive alarm armed (+A)
Max. current comfort control
Max. number codifying keys
SELF-POWERED CODIFIED 7125TNC SIREN (US models)
DESCRIPTION
The self-powered codified siren is an audible signalling device with high power designed to be installed in
the engine compartment of the vehicles, which can be connected to the alarm unit through the wiring
harness supplied with the kit.
disconnect the negative of the battery and only re-connect after the installation is complete.
Wires
BLACK initialled RB
BLACK initialled
BLACK initialled
BLACK initialled
Connect one end of the BLACK initialled V wire to the bonnet button and the other end to the alarm unit
GREEN wire.
WORKING
The electronic siren 7125TNC is supplied with a self-powering internal device that allows the working of the
siren also in absence of the power or if the connection wires to the unit are cut.
Through the codified system between alarm and siren, the alarm activates and de-activates both the
battery charging and the power of the siren.
The battery recharges only wi t h alarm disarmed. The self-power activates only with alarm armed and 3
minutes after the alarm disarming. Before de-activating the siren it is necessary to wait 4 minutes after the
alarm disarming.
MOUNTING
Mount the siren in the engine compartment of t h e vehicle using the screws and the bracket supplied with
the kit and a 8 mm adjustable wrench to tighten the nuts.
Mount the siren away from areas of intense heat and turn the acoustic ear trumpet to low.
Protects the wires from water and humidity isolating connection points with protective sheaths.
TECHNICAL DATA
Wiring connections (for the installer) :
Battery positive
ê
Battery negative
MB
ê
Gemini alarm PINK wire
S
ê
Gemini alarm BLUE wire
ê
L
Technical data
Power supply
12 V
Current absorption alarm ON
3 mA
Current absorption alarm OFF
7 mA
Audible tone
> 120 dB
10,5 ÷14,5VDC
5 mA
-30° + 85°
8A to 20° C
8A to 20° C
8A to 20° C
30 sec.
1A
100mA
3 (only US models)
Function
Advertisement
Table of Contents
