Table of Contents
Advertisement
Gemini 7024US is a modular alarm unit with ultrasonic sensors; studied to be
installed on vehicles equipped with original central door locking control.
Gemini 7024 is a modular alarm without ultrasonic sensor.
The systems Gemini 7024US a nd Gemini 7024 can be installed on vehicles (with
diesel or petrol engine) with a 12V battery with negative to earth.
Gemini 7024US.1 like 7024US without electronic keys.
Gemini 7024.1 like 7024 without electronic keys.
- Outlet for direction indicator lights - Blinker
- Volumetric and Perimetric protection (only for US models).
- Positive and negative control for vehicles equipped with Pack-comfort system.
- Engine immobilisation.
- Negative control for external supplementary siren.
- Automatic arming and "GARAGE " position function (only for US models).
- Emergency disarming through electronic key (only for 7024 and 7024US).
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
- Position the system wiring harness away from high voltage wires in order to avoid interference that may cause
damages to the system.
- On vehicles with a catalytic converter the engine immobilisation must be carried out on the fuel pump.
- If the system is supplied with volumetric sensors (art. 7024US), the transducers must be positioned at the top
of each windscreen pillar and away from the facia outlet.
- Connect the positive feeding of the alarm system to the battery positive terminal and the negative feeding of
the alarm system to the battery negative terminal or to the vehicle frame.
- IMPORTANT: to obtain a correct working of the automatic arming and the perimetrical protection
functions, it is COMPULSORY to connect the GREEN-BROWN wire to the door/boot switches.
The unit memorises the polarity of the arming and disarming controls from the vehicle 10 seconds
-
after the alarm feeding. The LED lights fix.
During this period it is possible to carry out only the "Blinker" exclusion.
CONNECTION TO THE RADIO RECEIVER
For vehicles with original positive control receiver, follow the fitting diagram A.
For vehicles with original negative control receiver, follow the fitting diagram B.
For vehicles with codified receiver with single control button, negative to rest, follow the fitting diagram C.
For vehicles with codified receiver with a double control button, negative to rest, follow the fitting diagram
D.
For vehicles with codified receiver with button or control button free to rest, follow the fitting diagram E.
For vehicles with codified receiver and central door locking closure control supplied with alarm connection,
follow the fitting diagram F.
NOTE: F
OR THE DIAGRAMS OF THE VEHICLES ASK TO THE CAR DISTRIBUTOR OF THE AREA
DESCRIPTION
DESCRIPTION
FUNCTIONS
FUNCTIONS
ULTRASONIC SENSOR ADJUSTMENT( only for 7024US)
The ultrasonic sensor adjustment is carried out while alarm armed with the sensor exclusion
function activated.
- Put the electronic key in the socket, the LED flashes for one second.
- Arm the alarm system with the vehicle original transmitter. The arming is signalled by 2
pulses of the direction indicator lights. Wait the end of the inhibit time.
- Put one hand in the vehicle and move it. The sensor detects the movement without triggering
the alarm; the LED switches on. If the LED does not switch on increase the sensitivity (fully
clockwise) and repeat test.
(
DISCONNECT THE NEGATIVE BATTERY TERMINAL AND RE
FUNCTIONS
Earth
Battery positive
Engine immobilisation (Max 8A)
Ignition live
Direction indicator lights
Door pin switches
Boot pin switch
Sensors inlet
Positive alarm armed
Self-powered siren control
Sel. alternative or continuous sound
Additional siren/horn control
Negative comfort control
Positive comfort control
Selection for automatic activation
Arming/disarming control
Refer to diagrams A, B, C, D, E, F.
NOTE: connect the 2- pin connectors of the wiring harness to the electronic key socket connectors
(only for US models).
- A
LARM ARMING WITH THE ORIGINAL TRANSMITTER
closing the doors of the vehicle.
indicator lights if the visualisation is not excluded.
- A
LARM ARMING WITH THE EXCLUSION OF THE ULTRASONIC AND EXTERNAL SEN SORS
put the electronic key in the appropriate socket before arming the alarm system. The arming
is signalled by 2 pulses of the direction indicator lights if the visualisation is not excluded.
Note: the sensor exclusion is obtained also with the function of automatic arming activated.
- A
: press on the transmitter's button at the same time of the vehicle's door
LARM DISARMING
opening. The disarming is signalled by 3 pulses of the direction indicator lights; 5 pulses if an
alarm condition has occurred (if the visualisation function is not excluded).
- A
LARM DISARMING THROU GH THE ELECTRONIC KEY
function put the electronic key in the appropriate socket. The disarming is signalled by 3
.
pulses; 5 pulses if an alarm condition has occurred (if the visualisation function is not
excluded).
WIRING CONNECTIONS
-
CONNECT AFTER THE IN STALLATION IS COMPLETE
WIRES COLOUR
ð ð BROWN
ð ð RED
ð ð 2 x GREY
ð ð YELLOW
ð ð 2 x ORANGE
ð ð GREEN-BROWN
ð ð GREEN
ð ð GREEN-BLACK
ð ð PINK
ð ð BLUE
ð ð BLACK (10cm.)
ð ð YELLOW-BLACK
ð ð WHITE-BLACK
ð ð RED-BLACK
ð ð YELLOW-GREEN (10 cm.)
ð ð YELLOW-RED, BROWN-RED,
YELLOW-BLUE WHITE-L. BLUE,
GREEN-BLUE.
WORKING DESCRIPTION
WORKING DESCRIPTION
: press on the original transmitter button while
The arming is signalled by one pulse of the direction
(
7024
ONLY FOR
AND
).
(US
):
MODELS
7024US): to obtain this
Advertisement
Table of Contents
