Advertisement
After use, push the on/off slide
4
downwards to switch off the
shaver.
Put the protection cap on the
5
shaver every time you have used
it, to prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 9).
Cleaning and maintenance
Never use scouring pads, abrasive
cleaning agents or aggressive liquids
such as petrol or acetone to clean
the appliance.
Regular cleaning guarantees better
shaving performance.
For the best cleaning results, we advise
you to use Philips Cleaning Spray
(HQ110).
You can also clean the shaver in the
following way:
Every week: shaving unit and
hair chamber
Switch off the shaver.
1
Clean the top of the appliance
2
with the cleaning brush
supplied (Fig. 10).
Press the release button slightly
3
downwards (1) and remove the
shaving unit (2) (Fig. 11).
Clean the inside of the shaving
4
unit and the hair chamber with
the cleaning brush (Fig. 12).
Put the shaving unit back onto the
5
shaver ('click') (Fig. 13).
Every two months: shaving
heads
Switch off the shaver.
1
Press the release button slightly
2
downwards (1) and remove the
shaving unit (2) (Fig. 11).
Push the sides of the central
3
spring towards each other (1) and
then lift the retaining frame out of
the shaving unit (2) (Fig. 14).
Slide the shaving heads out of the
4
retaining frame.
Hold your finger underneath the
shaving head to keep the cutter and
guard together.
Disassemble and clean the
5
shaving heads one by one (Fig. 15).
Note: Do not clean more than one cutter
and guard at a time, since they are all
matching sets. If you accidentally mix
up the cutters and guards, it may take
several weeks before optimal shaving
performance is restored.
Clean the cutter with the short-
6
bristled side of the cleaning
brush (Fig. 16).
Brush carefully in the direction of the
arrow.
Clean the guard with the cleaning
7
brush (Fig. 17).
Slide the shaving heads back into
8
the retaining frame and put the
retaining frame back into the
shaving unit.
Put the shaving unit back onto the
9
shaver ('click') (Fig. 13).
storage
Always put the protection cap
1
on the shaver after use, to
prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 9).
Put the shaver in the storage
2
pouch.
Replacement
Replace the shaving heads every two
years for optimal shaving results.
Replace damaged or worn shaving heads
with HQ4 Philips shaving heads only.
Switch off the shaver.
1
Press the release button slightly
2
downwards (1) and remove the
shaving unit (2) (Fig. 11).
Push the sides of the central
3
spring towards each other (1) and
then lift the retaining frame out of
the shaving unit (2) (Fig. 18).
Slide the shaving heads out of the
4
retaining frame.
Slide new shaving heads into the
5
retaining frame (Fig. 19).
Put the retaining frame back into
6
the shaving unit.
Put the shaving unit back onto the
7
shaver ('click') (Fig. 13).
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop
at www.shop.philips.com/service.
If the online shop is not available in
your country, go to your Philips dealer
or a Philips service centre. If you have
any difficulties obtaining accessories
for your appliance, please contact the
Philips Consumer Care Centre in your
country. You find its contact details in
the worldwide guarantee leaflet.
To retain the top performance of your
shaver, make sure you clean it regularly
and replace its shaving heads at the
recommended time.
shaving heads
-
We advise you to replace your
shaving heads every two years.
Always replace with HQ4 Philips
shaving heads. (Fig. 20)
UsB wall adapter
If you would like to purchase a USB
wall adapter to be able to charge the
shaver from the mains, only buy the
Philips USB wall adapter; type HX9200,
available through the Philips Consumer
Care Centre.
Cleaning
-
Use Philips Cleaning Spray
(HQ110) to clean the shaving
heads thoroughly.
Environment
-
Do not throw away the
appliance with the normal
household waste at the end of
its life, but hand it in at an official
collection point for recycling. By
doing this, you help to preserve
the environment (Fig. 21).
-
The built-in rechargeable battery
contains substances that may
pollute the environment. Remove
the battery before you discard
and hand in the appliance at an
official collection point. Dispose of
the battery at an official collection
point for batteries. If you have
trouble removing the battery, you
can also take the appliance to a
Philips service centre. The staff of
this centre will remove the battery
for you and will dispose of it in an
environmentally safe way (Fig. 22).
Removing the rechargeable
battery
Only remove the battery if it is
completely empty.
Disconnect the shaver from the
1
wall socket or from the USB port
and let the shaver run until it
stops.
Insert a flat-head screwdriver
2
between the plastic bottom of
the shaver and the socket for the
micro USB plug. Pry the bottom
off the shaver (Fig. 23).
Insert the flat-head screwdriver
3
between the housing of the
shaver and the printed circuit
board. Use force to separate the
housing halves and take out the
battery holder. (Fig. 24)
Insert the flat-head screwdriver
4
between the battery holder and
the battery. Apply some force to
break the connection strips. Take
out the battery (Fig. 25).
Do not connect the shaver to the
mains again after the rechargeable
battery has been removed.
guarantee and service
If you need service or information
or if you have a problem, please visit
the Philips website at www.philips.
com/support or contact the Philips
Consumer Care Centre in your
country. You find its phone number
in the worldwide guarantee leaflet. If
there is no Consumer Care Centre in
your country, go to your local Philips
dealer.
guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they
are subject to wear.
Troubleshooting
This chapter summarises the most
common problems you could encounter
with the appliance. If you are unable to
solve the problem with the information
below, visit www.philips.com/support
for a list of frequently asked questions or
contact the Consumer Care Centre in
your country.
Problem
Possible
Solution
cause
The
The shaving
Clean the
shaver
heads are
shaving heads
does not
dirty. You
thoroughly
shave as
have not
before you
well as it
cleaned the
continue
used to.
shaver well
shaving. See
enough or
chapter
you have
'Cleaning and
not cleaned
maintenance'.
it for a long
time.
Long hairs
Clean the
obstruct
cutters and
the shaving
guards with
heads.
the cleaning
brush supplied.
See chapter
'Cleaning and
maintenance'.
You mixed
Put each cutter
up the
in the other
cutters and
guard. If you
guards when
do not switch
you placed
the cutters, it
them back
may take 2 to
into the
3 weeks until
retaining
optimal shaving
frame after
performance is
cleaning.
restored.
The shaving
Replace the
heads are
shaving heads.
damaged or
See chapter
worn.
'Replacement'.
The
The re-
Recharge
shaver
chargeable
the battery.
does not
battery is
See chapter
work
empty.
'Charging'.
when
I push
the on/
off slide
upwards.
Advertisement
