Sony HBD-N590 Service Manual page 35

CONFIRMATION ITEM
1. Playback Operation Confi rmation
1-1. Test Disc
Part No. Description
J-6090-199-A BLX-104
J-6090-200-A BLX-204
J-2501-307-A CD (HLX-A1)
J-2501-305-A HLX-513
J-2501-306-A HLX-514
J-6090-077-A HLX-506
J-6090-078-A HLX-507
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select 23.976Hz/1080p.
2. Play "4.Motion picture".
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/HDMI.
Audio:
Speaker out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
* When the output of HDMI is 1080p/1080i/720p, the signal of
composite is not output.
It is necessary to lower the output of HDMI to 480p or 576p or
less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play "4.Motion picture".
3. Check whether player can play back or not.
(Check the picture and sound output)
3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select "1.Video Signal".
2. Play "1.Color bar 100%".
(Check the picture and sound output)
3. Return to Menu.
4. Play "Demonstration 4:3" or "Demonstration 16:9".
(Check the picture and sound output)
1-2. Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.
Note: "AV Sync." doesn't operate.
HBD-N590/N790W/N890W/N990W/N995W/T79
2. Networking Confi rmation
Confi rm it according to the following procedure when you confi rm
the connection of the network.
Note: Do not execute "Network Connection Diagnostics" of "Network
Layer
Single Layer
Dual Layer
Procedure:
1. Connect the router with the unit with LAN cable.
2. Turn on the power of the unit and the router.
Single Layer (NTSC)
3. Press the [HOME] button on the remote commander, and the
Dual Layer (NTSC)
Single Layer (PAL)
4. Select "Setup"  "Network Settings", and press the [ ] but-
Dual Layer (PAL)
5. Select "Internet Settings" and press the [ ] button on the re-
6. Select "View Network Status" and press the [ ] button on the
7. Confi rm IP address are displayed in "IP Address", "Subnet
Settings" of the home menu with only the router connected.
home menu is displayed.
ton on the remote commander.
mote commander.
remote commander.
Mask" and "Default Gateway".
Physical Connection:
Internet Access:
IP Address Setting:
IP Address:
Subnet Mask:
Default Gateway:
DNS Settings:
Primary DNS:
Secondary DNS:
MAC Address:
XXXX
XXXX
XXXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
35