Table of Contents
Advertisement
System Connections
(Indoor Pan/tilt Head System)
$ Example System Setup
Color monitor
(75 Ω terminator)
Zoom/focus control
Iris control
Video
Convertible
camera
Camera cable:
AW-CA50T15
Servo control
Pan/tilt head
zoom lens
control
Camera control
Option switch
Gen-lock
control:
Unnecessary if no
Video
optional unit is
connected.
Lamp control:
Unnecessary if no
DC15V
halogen lamp is used.
Halogen lamp
P O W E R
O F F
O N
Pan/tilt head AC
Contact
adapter:
AW-PS300
Optional unit
Adjustment such as cable compensation, gen-
lock adjustment, and total pedestal adjustment
should be applied to the video signals output
from the AW-HB505.
S-Video
Multi port hub:
AC adapter:
AW-HB505
AW-PS505
C A B L E C O M P
1
2
3
4
5
P O W E R
O F F
O N
Y
C
Y
C
Y
C
Y
C
Y
C
O I
M u l t l
P o r t
H u b
A W - H 8 5 0 5
Preview Video
Gen-lock
Camera control
Pan/tilt head control
Multi control hub:
AW-HB605
AC adapter:
O I
AW-PS505
Preview color
monitor
(75 Ω terminator)
Preview Video
Multi hybrid control
panel:
AW-RP505
Priority
switchbox
AC adapter:
AW-PS301
Camera control
Pan/tilt head control
Preview Video
16
Operations
1.
Turn the power on.
Turn on the power control switches of
the AC adapters of the pan/tilt heads
and control panels, as well as the AC
adapter and power control switch of the
multi control hub.
If the system incorporates a multi port
hub, turn on the power control switch of
the multi port hub and the power switch
of its AC adapter.
2.
Press the button on the priority
switchbox connected to the control
panel you wish to operate. This
activates the connected control panel.
If the system incorporates a multi hybrid
control panel, use the camera and
pan/tilt head selector switch on the multi
hybrid control panel to select a pan/tilt
head. (The control panel is activated
once its memory switch stops flashing
and goes dark.)
<Notes>
O Immediately after the power is turned
on the system is in a status in which
no control panel is selected. After
turning the power on, do not fail to
press
the
priority
switchbox
connected to the control panel you
wish to operate. After this operation
is performed the power supply to the
camera and pan/tilt head turns on.
O The active control panel is always the
one
connected
to
the
priority
switchbox pressed last.
3.
Perform
the
mounting
balance
adjustment on the cameras. For detailed
instructions, refer to the manuals
accompanying the relevant equipment.
4.
Set the limits to the range of movement
for the pan/tilt head (limiter). For
detailed instructions, refer to the
manuals accompanying the relevant
equipment.
5.
If the system incorporates a hybrid
control panel or multi hybrid control
panel, perform video signal cable
compensation,
G/L
(gen-lock)
adjustment,
and
total
pedestal
adjustment. Also set the switches as
appropriate. For detailed instructions,
refer to the manuals accompanying the
relevant equipment.
<Note>
After
performing
G/L
(gen-lock)
adjustment
and
total
pedestal
adjustment, set the control panel's G/L
phase adjustment switch to the OFF
position. The instruction manual of the
hybrid control panel states that this
switch should be left in the ON position,
but it should be set to OFF on systems
using the multi control hub.
6.
Store the preset settings for the
cameras and pan/tilt heads in memory
(systems incorporating hybrid control
panel or multi hybrid control panel only).
For detailed instructions, refer to the
manuals accompanying the relevant
equipment.
<Note>
The preset settings are stored in the
memory of the pan/tilt head. When new
preset settings are stored in memory, all
the previous settings (including those
stored in memory using the control
panel) are overwritten.
The adjustments and settings described
3
6
in steps
though
above may be
omitted if no changes need to be made to
the current adjustments and settings.
17
Advertisement
Table of Contents
