Panasonic WV-NP1000 Operating Instructions Manual page 15

Important
• Make sure that the installing place is strong enough to
support the total weight of the camera and the camera
mounting bracket.
• Safety wire differs depending on the model and installa-
tion height of camera mounting bracket (option).
Procure the optional safety wire kit suited for installa-
tion. Refer to "Select Safety Wire Kit." for details.
Step 3
Connect a coaxial cable (optional) to the video out connec-
tor. (One BNC plug is provided with the camera.)
AC24V
IN
VIDEO OUT
1-L POWER
Coaxial cable
2-N
SD CARD 1 GND
(optional)
2 DAY/NIGHT IN
3
AUX OUT
4 ALARM OUT
LINK
5 ALARM IN
GND
1
2
10BASE-T/
3
100BASE-TX
4
5
ACT
(The illustration above is of the WV-NP1004.)
Step 4
<For the WV-NP1000>
Connect the AC power cord (provided as a standard
accessory) between the AC inlet of the camera and a 220 V
– 240 V AC 50 Hz outlet.
Power cord (provided)
Ferrite core
Read this label
Note:
• Connect the power cord firmly.
<For the WV-NP1004>
Connect the AC inlet on the rear of the camera and the AC
outlet with a power cable.
Power cable
AC 24V,
50 Hz
Connect to the
video monitor, etc.
220V - 240V ~ 50Hz
VIDEO OUT
POWER
SD CARD 1 GND
2 DAY/NIGHT IN
3 AUX OUT
4 ALARM OUT
LINK
5 ALARM IN
1
2
10BASE-T/
3
100BASE-TX
4
5
ACT
AC24V
IN
VIDEO OUT
1-L
POWER
2-N
SD CARD 1 GND
2 DAY/NIGHT IN
3 AUX OUT
4 ALARM OUT
LINK
5 ALARM IN
GND
1
2
10BASE-T/
3
100BASE-TX
4
5
ACT
Step 5
Connect a LAN cable (category 5 or better) to the network
connector on the rear of the camera.
AC24V
IN
1-L
2-N
LAN cable
Step 6
Connect an external device to the EXT I/O connector.
When connecting an external device, remove 9 mm – 10
mm of the outer jacket of the cable and twist the cable core
to prevent the short circuit first.
Specification of cable (wire): AWG22 - AWG28
AC24V
IN
VIDEO OUT
1-L
POWER
2-N
SD CARD 1 GND
2 DAY/NIGHT IN
3 AUX OUT
4 ALARM OUT
LINK
5 ALARM IN
GND
1
2
10BASE-T/
3
100BASE-TX
4
5
ACT
GND
DAY/NIGHT IN (color/BW in)
AUX OUT
ALARM OUT
ALARM IN
<Ratings>
ALARM IN: 5 V DC pull-up, Drive ability 0.5 mA or more
ALARM OUT: Open collector output
OPEN: Open or DC 4 V – DC 5 V
Maximum applied voltage: 20 V
CLOSE: Make contact with GND (50 mA or less)
AUX OUT: Open collector output
OPEN: Open or DC 4 V – DC 5 V
Maximum applied voltage: 20 V
CLOSE: Make contact with GND (50 mA or less)
DAY/NIGHT IN: 5 V DC pull-up, Drive ability 0.5 mA or
more
Color: Open
BW: Short circuit
* To validate the color/BW input, select "EXT" for "BW
MODE". (→ page 18)
Important:
• Do not connect 2 wires or more directly to a terminal.
When it is necessary to connect 2 wires or more, use a
splitter.
• Connect an external device with verifying that the rat-
ings are within the specifications above.
VIDEO OUT
POWER
1 GND
SD CARD
2 DAY/NIGHT IN
3 AUX OUT
4 ALARM OUT
LINK
5 ALARM IN
GND
1
2
10BASE-T/
3
100BASE-TX
4
5
ACT
Single core, twisted
Cut
Approx. 9 mm - 10 mm
15