Speaker Set (Speaker Mode Settings) - Yamaha RX-V1300RDS Owner's Manual

4
Press j / i once to enter the setup mode of
the selected item.
The last setting you adjusted appears on the video
monitor or on the front panel display.
+
TV VOL
CH CH
TV MUTE
– +
SELECT
PRESET PRESET
TV VOL
–
Depending on the item, press u/d to select a sub
item.
+
TV VOL
CH CH
TV MUTE
– +
SELECT
PRESET PRESET
TV VOL
–
5
Press j / i repeatedly to change the setting
of the item.
+
TV VOL
CH CH
TV MUTE
– +
SELECT
PRESET PRESET
TV VOL
–
6
Press u/d repeatedly until the menu
disappears or simply press one of the DSP
program group button to exit from the SET
MENU.
+
TV VOL
CH CH
or
TV MUTE
+
–
SELECT
PRESET PRESET
TV VOL
–
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby
mode. However if the power cord is disconnected from
the AC outlet, or the power supply is cut for more than
one week, the stored data will be lost. If so, adjust the
items again.
0109V1300_56-68_EN-GB.p65
2 LOW FRQ TEST
≥ T E S T T O N E ... ... ... O F F
O U T P U T ... M A I N L / R
F R Q ... ... ... ... ... ... ... ... 8 8 H z
2 LOW FRQ TEST
T E S T T O N E ... ... ... O F F
≥ O U T P U T ... M A I N L / R
F R Q ... ... ... ... ... ... ... ... 8 8 H z
2 LOW FRQ TEST
≥ T E S T T O N E ... ... ... ... O N
O U T P U T ... M A I N L / R
F R Q ... ... ... ... ... ... ... ... 8 8 H z
ROCK
HALL CHURCH JAZZ CLUB CONCERT
1 2 3 4
ENTER- MUSIC TV MOVIE
TAINMENT VIDEO THEATER THEATER 1
5 6 7 8
MOVIE /DTS
EX/ES
THEATER 2 SUR. SELECT
9 10 11 12
+
0 10 CHP/INDEX
57
1 SPEAKER SET (speaker mode
settings)
Use this feature to select suitable output modes for your
speaker configuration.
Notes
• When 96-kHz sampling digital signals are input to this unit,
level adjustments in items 1B,1E and 1F are possible, but those
in items 1A,1C and 1D are not affected.
• When 6CH INPUT is selected as the input source, level
adjustments in items 1A through 1E are not affected.
y
• Select SML if the woofer diameter of you speaker is smaller
than 16 cm. If it is larger than 16 cm, select LRG.
I 1A CENTER SP (center speaker
mode)
By adding a center speaker to your speaker configuration,
this unit can provide good dialog localization for many
listeners and superior synchronization of sound and
images. The OSD shows a large, small or no center
speaker depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have a large center speaker. The entire
range of the center channel signal is directed to the center
speaker.
1A CENTER SP
L R G S M L N O N E
SML
Select this if you have a small center speaker. The low-
frequency signals (90 Hz and below) of the center
channel are directed to the speakers selected with "1E
LFE/BASS OUT".
1A CENTER SP
L R G S M L N O N E
NONE
Select this if you do not have a center speaker. All of the
center channel signal are directed to the left and right
main speakers.
1A CENTER SP
L R G S M L N O N E
2002.11.07, 12:09
SET MENU
57