Page 1
Power antenna control Tuning range EXR-C205: lead/Power amplifier 87.5-107.9 MHz control lead/Telephone XR-C340: mute control lead (XR-C340 only) FM tuning interval: Rear line out (1) 50 kHz/200 kHz Tone controls Bass ±8 dB at 100 Hz switchable Treble ±8 dB at 10 kHz 87.5-108.0 MHz...
TABLE OF CONTENTS SERVICING NOTES GENERAL ..............3 Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚ C dur- Location of Controls ............3 Resetting the Unit ............3 ing repairing. • Do not touch the soldering iron on the same conductor of the Detaching the Front Panel ..........
SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. FRONT PANEL ASS’Y 1 Push the button (release). 2 Remove the front panel ass’y to the direction of the arrow A . COVER ASS’Y 3 cover ass’y –...
Page 11
SUB PANEL, MECHANISM DECK (MG-25A-136) 5 screw (PTT2.6 × 6) 3 connector (CN302) 6 mechanism deck (MG-25A-136) 4 flexible flat cable (CN301) 2 sub panel 1 three screws (PTT2.6 × 8) 1 three screws (PTT2.6 × 8) 4 eight screws MAIN BOARD, HEAT SINK (PTT2.6 ×...
SECTION 3 ASSEMBLY OF MECHANISM DECK Note: Follow the assembly procedure in the numerical order given. HOUSING 7 Hold the hanger by bending the claw. 5 Fit projection on C part. 2 Install the hanger onto 1 Install the catch to the hanger. two claws of the housing.
Page 13
LEVER (LDG-A) / (LDG-B) shaft A 2 Pull the lever in the shaft B shaft A arrow direction. shaft C shaft B 1 Fit the lever (LDG-A) on 4 type-E stop ring 2.0 shafts A – C and install it. 3 Fit the lever (LDG-B) on shafts A and B and install it.
SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS 1. Clean the following parts with a denatured-alcohol-moistened TAPE DECK SECTION 0 dB=0.775 V swab: playback head pinch roller Tape Speed Adjustment rubber belt capstan idlers Procedure: 1. Put the set into the FWD PB mode. 2.
SECTION 6 DIAGRAMS 6-1. IC PIN FUNCTION DESCRIPTION • IC501 µD17708GC-545-3B9 (MASTER CONTROLLER) Pin No. Pin Name Function ILLIN ILLIN signal detection pin 2, 3 POS3, 2 Tape position detection pin 4, 5 POS0, 1 TAPEON Tape power supply control pin CM_ON Capstan motor control pin LM_LOD...
Page 17
Data output pin (for SONY BUS) UNISI Data input pin (for SONY BUS) UNICKO Clock output pin (for SONY BUS) BUSON BUS ON control signal output pin (for SONY BUS) SYSRST System reset signal output pin VREG CPU regurator output pin –...
Page 19
• Waveform IC351 MM1322XFBE 1 IC501 &¶ 8 OUT2 3.2 Vp-p OUT1 222 ns IC581 BA8270F-E2 BUS ON BUS ON SWITCH RESET SWITCH BUS ON CLK IN BATTERY BATT BU IN SWITCH VREF DATA IN DATA DATA OUT IC611 BA3918-V2 REGULATOR OVER VOLTAGE PROTECT...
SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • SEMICONDUCTORS When indicating parts by reference number, please include the board. parts list may be different from the parts speci- In each case, u: µ, for example: fied in the diagrams or the components used on uA.