Riello RG5D Installation, Use And Maintenance Instructions
  1. Manuals
  2. Brands
  3. Riello Manuals
  4. Burner
  5. RG5D
  6. Installation, use and maintenance instructions

Riello RG5D Installation, Use And Maintenance Instructions

Light oil burner
Hide thumbs Also See for RG5D:
Table of Contents

Advertisement

Quick Links

Montage und Bedienungsanleitung
Manuel d'entretien
Installation, use and maintenance instructions
Installatie-, gebruiks- en onderhoudsvoorschriften
Instrucciones de instalación, uso y mantenimiento
Οδηγίες εγκατάστασης, χρήσης και συντήρησης
Öl-Gebläsebrenner
D
Brûleur fioul domestique
F
Light oil burner
GB
Stookoliebrander
NL
Quemadores de gasóleo
E
Καυστήρας Πετρελαίου
GR
Zweistufiger Betrieb
Fonctionnement à 2 allures
Two stage operation
Parts Available from
Tweetrapsbranders
Funcionamiento de dos llamas
ιβάθµια λειτουργία
www.sparesgiant.com
CODE - CÓDIGO
ΚΩ ΙΚΟΣ
3739850
MODELL - MODELE
MODEL - MODELO - ΜΟΝΤΕΛΟ
RG5D
TYP - TYPE
TIPO - ΤΥΠΟΣ
398T1
2902312 (5)

Advertisement

Table of Contents
loading

Related Manuals for Riello RG5D

Summary of Contents for Riello RG5D

  • Page 1 Fonctionnement à 2 allures Two stage operation Parts Available from Tweetrapsbranders Funcionamiento de dos llamas ιβάθµια λειτουργία www.sparesgiant.com CODE - CÓDIGO MODELL - MODELE TYP - TYPE ΚΩ ΙΚΟΣ MODEL - MODELO - ΜΟΝΤΕΛΟ TIPO - ΤΥΠΟΣ 3739850 RG5D 398T1 2902312 (5)

  • Page 2: Table Of Contents

    INDEX BURNER DESCRIPTION ... . WORKING ..... . . 1.1 Burner equipment ....4.1 Combustion adjustment.

  • Page 3: Technical Data

    TECHNICAL DATA 2.1 TECHNICAL DATA TYPE 398 T1 Output - Thermal power 8 / 12 – 25 kg/h – 95 / 142 – 296 kW Fuel Light oil, viscosity 4 – 6 mm /s at 20 °C ± Electrical supply Single phase, 50Hz 230 V Motor...

  • Page 4: Installation

    INSTALLATION THE BURNER MUST BE INSTALLED IN CONFORMITY WITH LEGISLATION AND LOCAL STANDARDS. 3.1 BOILER FIXING Put on the flange (1) the screw and two nuts, (see fig. 3). Widen, if necessary, the insulating gasket holes (4), (see fig. 4). Fix the flange (1) to the boiler door (3) using screws (5) and (if necessary) the nuts (2) interposing the insulating gasket (4), (see fig.

  • Page 5: Hydraulic Systems

    3.3 HYDRAULIC SYSTEMS WARNING: Fig. 8 The pump is designed to allow working with two pipes. In order to obtain one pipe working it is necessary to unscrew the return plug (2), remove the by-pass screw (3) and then screw again the plug (2), (see fig.

  • Page 6: Electrical Wiring

    3.4 ELECTRICAL WIRING NOTES: WARNING – Wires of min. 1 mm section. (Unless requested otherwise DO NOT EXCHANGE by local standards and legislation). NEUTRAL WITH PHASE – The electrical wiring carried out by the installer must be in compliance with the rules in force in the Country. Connect 2nd stage thermostat between clamps T6 - T8 50Hz 230V by removing the bridge.

  • Page 7: Working

    WORKING 4.1 COMBUSTION ADJUSTMENT In conformity with Efficiency Directive 92/42/EEC the application of the burner on the boiler, adjustment and testing must be carried out observing the instruction manual of the boiler, including verification of the CO and CO concentration in the flue gases, their temperatures and the average temperature of the water in the boiler. To suit the required appliance output, choose the proper nozzle and adjust the pump pressure, the setting of the combustion head, and the air damper opening in accordance with the following schedule.

  • Page 8: Combustion Head Setting

    4.3 COMBUSTION HEAD SETTING (see fig. 12, page 6) It depends on the output of the burner and is carried out by rotating clockwise or counterclockwise the setting screw (6) until the set-point marked on the regulating rod (7) is level with the outside plane of the nozzles- holder assembly (1).

  • Page 9: Burner Start-Up Cycle

    4.6 BURNER START-UP CYCLE Normal Lock-out due to failure to light 1 st stage thermostat 2 nd stage thermostat Motor Ignition transformer 1 st stage valve 1 st stage flame 2 nd stage valve 2 nd stage flame Lock-out lamp 3 –...

  • Page 10: Faults / Solutions

    FAULTS / SOLUTIONS Here below you can find some causes and the possible solutions for problems that could cause a failure to start or a bad working of the burner. A fault usually makes the lock-out lamp light which is situated inside the reset button of the control box (4, fig.
  • Page 11 Parts Available from www.sparesgiant.com...

Table of Contents