HP A5120 EI Configuration Manual page 102
Hide thumbs
Also See for A5120 EI:
- Command reference manual (225 pages) ,
- Configuration manual (197 pages) ,
- Installation manual (91 pages)
Table of Contents
Advertisement
[DeviceD-GigabitEthernet1/0/1] quit
[DeviceD] interface gigabitethernet 1/0/2
[DeviceD-GigabitEthernet1/0/2] undo shutdown
[DeviceD-GigabitEthernet1/0/2] quit
Configure Device B.
3.
# Create VLANs 1 through 30.
<DeviceB> system-view
[DeviceB] vlan 1 to 30
# Configure GigabitEthernet 1/0/1 as a trunk port, and assign it to VLANs 1 through 30. Enable flush
message receiving on it, and configure VLAN 10 and VLAN 20 as the receive control VLANs.
[DeviceB] interface gigabitethernet 1/0/1
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30
[DeviceB-GigabitEthernet1/0/1] smart-link flush enable control-vlan 10 20
[DeviceB-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 as trunk ports, and assign them to
VLANs 1 through 30. Disable the spanning tree feature and enable flush message receiving on them,
and configure VLAN 10 and VLAN 20 as the receive control VLANs.
[DeviceB] interface gigabitethernet 1/0/2
[DeviceB-GigabitEthernet1/0/2] port link-type trunk
[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30
[DeviceB-GigabitEthernet1/0/2] undo stp enable
[DeviceB-GigabitEthernet1/0/2] smart-link flush enable control-vlan 10 20
[DeviceB-GigabitEthernet1/0/2] quit
[DeviceB] interface gigabitethernet 1/0/3
[DeviceB-GigabitEthernet1/0/3] port link-type trunk
[DeviceB-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30
[DeviceB-GigabitEthernet1/0/3] undo stp enable
[DeviceB-GigabitEthernet1/0/3] smart-link flush enable control-vlan 10 20
[DeviceB-GigabitEthernet1/0/3] quit
Configure Device E.
4.
# Create VLANs 1 through 30.
<DeviceE> system-view
[DeviceE] vlan 1 to 30
# Configure GigabitEthernet 1/0/1 as a trunk port, and assign it to VLANs 1 through 30. Enable flush
message receiving on it, and configure VLAN 10 and VLAN 20 as the receive control VLANs.
[DeviceE] interface gigabitethernet 1/0/1
[DeviceE-GigabitEthernet1/0/1] port link-type trunk
[DeviceE-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30
[DeviceE-GigabitEthernet1/0/1] smart-link flush enable control-vlan 10 20
[DeviceE-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 as trunk ports, and assign them to
VLANs 1 through 30. Disable the spanning tree feature and enable flush message receiving on them,
and configure VLAN 10 and VLAN 20 as the receive control VLANs.
[DeviceE] interface gigabitethernet 1/0/2
[DeviceE-GigabitEthernet1/0/2] port link-type trunk
97
Advertisement
Table of Contents
Troubleshooting
