Test Mode - Kenwood KDC-1032 Service Manual

How to enter the test mode
• Press Preset [1] and Preset [3] keys simultaneously to re-
set the unit.
How to clear the test mode
Reset. (Do not clear by Power OFF and ACC OFF.)
Initial conditions of the test mode
• Source is STANDBY.
• Displays lights are all turned on.
• The volume is at -10dB (The display is 30).
• CRSC is OFF, regardless of whether there are switching
functions or not.
• LOUD is OFF.
• SYSTEM Q is NATURAL (FLAT).
• BEEP should always work by pressing a key.
Test mode specification for TUNER
• TUNER (FM) Preset [4] key shall be 98.3MHz.
CD receiver test mode specifications
• Forced discharging operation is prohibited at reset start. Note
that a CD is not to be recognized by reset when it is in-
serted.
• [Track up] key triggers a jump to the following tracks.
No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →
No. 22 → No. 14 → No. 9 (recursive)
• [Track down] key moves back to the previous track from the
current track.
• Preset [1] key triggers a jump to No. 28.
• Preset [2] key triggers a jump to No. 14. (Scan function is
invalid.)
Audio adjust mode
• Pushing the [VOL] key enters the audio function mode.
• The initial item is Fader. (FAD → BALANCE → BASS →
MID → TRE)
• Use [AM/FM] key to switching items.
• Use [Seek Up/Down] key to switching the adjusted value.
• Adjust Fader/Balance to three levels (15 ↔ 0 ↔ 15) with
Volume up/down. (initial value: 0)
• Adjust Bass/Middle/Treble to three levels (-8 ↔ 0 ↔ +8)
with Volume up/down. (initial value: 0)

TEST MODE

• Pressing the [VOL] key for more than a second enters the
audio setup mode.
• Use [AM/FM] key to switching items.
• Use [Seek Up/Down] key to switching the adjusted value.
• Adjust Volume offset to two levels (-8 ↔ 0). (initial value: 0)
• Initialize everything with the [Track-Up] key in the standby
source.
• Pressing [∗] key on the remote controller enters the audio
adjustment mode. (Use [∗] key to cancel. KDC-132CR only)
• Continuous feed with a remote controller shall not be used.
Pressing a key activates a motion. (KDC-132CR only)
Special display when all lights are on
The following information will be displayed by pressing the
preset key when STANDBY indicators are on.
[1] key • Press [1] key. The current destination SW is displayed.
(Display) TP-X
• Press a key while the destination SW is displayed.
Version display (month, date, hour, minute in 8 digits)
(Display) XXXX
[2] key • All LCD light up.
[3] key • Press the key for less than a second: Power-on time
display (STANDBY time should not be counted).
• Press the key for more than 2 seconds while the
power-on time is displayed: The power-on time is
cleared.
(Display) Pon_x
[4] key • Press the key for less than a second: CD operation
time display.
• Press the key for more than 2 seconds while the CD
operation time is displayed: CD operation time is
cleared.
(Display) PLY_x
[5] key • Press the key for less than a second: CD EJECT
count display.
• Press the key for more than 2 seconds while the CD
EJECT count is displayed: CD EJECT count is
cleared.
(Display) EJC_x
KDC-1032/132/132CR
KDC-133/233/234SGY
xxxx
XXXX MAX 60000 (time)
XXXX MAX 60000 (time)
XXXX MAX 60000 (time)
9