Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DTS XR7 WASH
Summary of Contents for DTS XR7 WASH
- Page 1 X R 7...
- Page 2 X R 7 INDEX: 1- Technical Features PG 1 2- Important Safety Information PG 2 2.1 Fire Prevention 2.2 Prevention Of Electric Shock 2.3 Protection Against Ultraviolet Radiation 2.4 Safety 2.5 Level Of Protection Against The Penetration Of Solid And Liquid Matter 3- Mounting The Lamp PG 3 3.1 Lamp Alignment...
-
Page 3: Technical Features
1- TECHNICAL FEATURES - New motorized moving head - ABS cover - 200mm fresnel lens - MSR575/2 lamp - Control: max 16 channels DMX - Fast, silent and precise movement - Position controlled pan (540°) and tilt (320°) by encoder - Motorized zoom (16°-28°) - Colour mixing by CMY - Colour wheel with 6 dichroic high chromatic yield filters +2 filters for... -
Page 4: Important Safety Information
2- IMPORTANT SAFETY INFORMATION 2.1 Fire prevention: 1. XR7 Wash uses a Philips 575 MSR/2 or MSD 575/2 lamp. The use of any alternative lamp is not recommended and will null and void the fixture's warranty. 2. Never locate the fixture on any flammable surface. -
Page 5: Mounting The Lamps
get as high as 350° C. Always check that the lamp is cold before attempting to remove it. In any case, only open the appliance 10 minutes after it has been turned off. 3- MOUNTING THE LAMPS Warning: turn power off before opening the appliance. Philips 575 MSR/2 Power 575W Luminous flux 49,000 lm... -
Page 6: Voltage And Frequency
5.1 Safety chain We recommend the use of a safety cable or chain connected to the Xr7 Wash and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit. -
Page 7: Mains Connection
The projector should never be installed in places that lack a constant flow of air. The ambient temperature should not exceed 35°C. 6- MAINS CONNECTION Xr7 Wash operates at voltage 230V at 50 or 60Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. -
Page 8: Dmx Signal Connection
Protection The use of a thermal magnetic circuit breaker is recommended for each Xr7 Wash. A good earth connection is essential for the correct operation of the projector. 7- DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 (1990) signal. Connection between the control box and the projector or between projectors must be carried out using a two pair screened ø0.5 mm cable and a CANNON... -
Page 9: Dmx Addresses
DMX mixer allots it. If you have a 12 channel controller, set your Xr7 Wash to 10 CH MODE. The first projector will have an A001 address and if you want to select the next projector, then... -
Page 10: Display Functions
DOWN ENTER The Xr7 Wash display panel shows all the functions available. Using these functions, it is possible to change some of the parameters and to add some functions. Changing the DTS setting can vary the functions of the appliance so that it does not respond to the DMX 512 used to control it. - Page 11 Up-Down ENTER RESET T o reset all motors function MENU Up-Down ENTER ENTER DEFAULT T o restore default setting (set by DTS) MENU ENTER Up-Down Pcb 8 motors . Pcb PAN&TILT SOF TWARE VERSION Electronic card software version. MENU Up-Down...
- Page 12 Automatic operation (auto) XR7 can work in automatic mode without a DMX controller. First of all connect the projectors with a DMX cable (picture below). MASTER IN OUT IN OUT To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO appears on the display, at this point press enter.
-
Page 13: Error Messages
16 scenes will be played through even if not programmed. 9.2 Pan & Tilt speed (SPEE) (default: 2) You can set the PAN and TILT engines at high speed on your Xr7 Wash. Press menu until you see SPEE. -
Page 14: Hidden Menu
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED) -Reset the Xr7 Wash (reset from the display projector, not from the DMX controller!). -While reset is working, press the MENU and ENTER keys at the same time. -
Page 15: Fans And Air Passages
12- OPENING UP THE PROJECTOR HOUSING It is possible to inspect the inside of the projector by removing the cover as indicated below. WARNING! REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS. 1) Loosen the screws which fix the upper and lower covers (photo 1) and unscrew the side covers (photo 2). -
Page 16: Electrical Components
13.6 Fuse replacement Locate the fuse, which protects the lamp and electronics, in the base of the Xr7 Wash. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary. - Page 17 à à à à à Ã8C6II@GÃHP9@Ãà %Ãiv‡Ãà 'Ã8C6II@GÃHP9@Ã'Ãiv‡Ã 9@A6VGUÃT@UUDIBT à à à à à à à à DEFAULT CMY COLOUR DEFAULT CMY COLOUR COLOUR COLOUR MACRO CMY/COLOUR MACRO CMY/COLOUR DIMMER/ SHUTTER DIMMER/ SHUTTER PAN msb TILT msb TILT EFFECT EFFECT ZOOM ZOOM PAN lsb...
- Page 18 à à $% %'à à 7vp‚y‚ˆ…Ã$%à %( ' à à 8‚y‚ˆ…%à '! (&à à 7v8‚y‚ˆ…Ã%uv‡rà ('!à à Svtu‡Ã…h‡v‚ƃrrqà Àh‘à ! !"à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ!à !#!%à à Svtu‡Ã…h‡v‚ƃrrqÃ"à !&!(à à Svtu‡Ã…h‡v‚ƃrrqÃ#à ! ! !à à Svtu‡Ã…h‡v‚ƃrrqÃ$à ! "! $à à Svtu‡Ã…h‡v‚ƃrrqÃ%à ! %! 'à Ã...
- Page 19 à à !%! $à ! à Ayh†uÃpy‚†rqƃrrqÃ!à ! %!!$à !!à Ayh†uÃpy‚†rqƃrrqÃ"à !!%!"$à !"à Ayh†uÃpy‚†rqƃrrqÃ#Àh‘à 8‚y‚ˆ…QhUvy‡Hhp…‚Ãvà !"%!#$à !#à 7yhpx‚ˆ‡Ã !#%!$$à !$à Pƒrà à à à DMX CHANNEL $à Parameter: ÃQ6IÀ†i DMX CHANNEL %à Parameter: ÃUDGUÀ†i DMX CHANNEL &à Parameter: Ã@AA@8U Move DMX range Mid point range...
- Page 20 à à à %Ã8C6II@GÃHP9@Ãà %iv‡Ãà à à #Ã8C6II@GÃHP9@ÃÃ'Ãiv‡Ã PAN msb PAN lsb TILT TILT msb SPEED MOVEMENT TILT lsb DIMMER SPEED MOVEMENT SHUTTER DIMMER COLOUR SHUTTER CYAN COLOUR MAGENTA CYAN YELLOW MAGENTA SPEED CMY / DIMMER YELLOW MACRO CMY / COLOUR SPEED CMY / DIMMER EFFECTS MACRO CMY / COLOUR...
- Page 21 à à DMX CHANNEL &à Parameter: ÃTCVUU@S Move DMX range Mid point range Mode Option Function Value DMX value (degrees) (à à 7yhpx‚ˆ‡Ã Strobe random speed !"à à !#"&à à T‡…‚irƃrrqà Àv "'$ à à T‡…‚irƃrrqÃ!à $!%$à à T‡…‚irƃrrqÃ"à %%&(à Ã...
- Page 22 à à ! "! $à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ%à ! %! 'à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ&à ! (!! à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ'à !!!!!#à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ(Àvà !!$!!'à à T‡‚ƒÃ !!(!" à à Grs‡Ã…‚‡h‡v‚ƃrrqà Àvà !"!!"#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ!à !"$!"&à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ"à !"'!#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ#à !# !#"à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ$Ã...
- Page 23 à à (degrees) (à I‚ÃAˆp‡v‚à !!$$à Hhp…‚à DMX CHANNEL #à Parameter: Ã@AA@8UT Move DMX range Mid point range Mode Option Function Value DMX value (degrees) (à #!à I‚Ãrssrp‡Ã !"(à !&à A…‚†‡Ã #!$$à ! "à 7rh€ÃTuhƒrà DMX CHANNEL $à Parameter: ÃaPPH Move...
- Page 24 à à Ã8C6II@GÃHP9@ÃÃ'Ãiv‡ÃÃà à 1 CYAN 2 MAGENTA 3 YELLOW 4 DIMMER SHUTTER 5 PAN 6 TILT 7 COLOR 8 MACRO / CMY COLOR 9 EFFECTS 10 ZOOM DMX CHANNEL à Parameter: Ã8`6I Move DMX range Mid point range Mode Option Function Value...
- Page 25 à à !% "$à à T‡…‚irƃrrqÃ#à "% #$à à T‡…‚irƃrrqÃ$à #% $$à à T‡…‚irƃrrqÃ%Àh‘à $% %$à à Ayh†uƒrƃrrqà Àvà %% &$à à Ayh†uƒrƃrrqÃ!à &% '$à à Ayh†uƒrƃrrqÃ"à '% ($à à Ayh†uƒrƃrrqÃ#Àh‘à (%!$à à Ayh†uÃpy‚†rqƃrrqà Àvà !%! $à à Ayh†uÃpy‚†rqƃrrqÃ!à ! %!!$à Ã...
- Page 26 à à !"!!"#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ!à !"$!"&à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ"à !"'!#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ#à !# !#"à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ$à !##!#%à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ%à !#&!#(à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ&à !$!$!à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ'à !$"!$$à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ(Àh‘à DMX CHANNEL 'à Parameter: ÃH68SPÃ8H`ÃÃ8PGPVS Move DMX range Mid point range Mode Option Function Value DMX value...
- Page 27 Ã Ã $ÃHPUPSÃ68UV6UPSÃ86S9 9DTQG6` XCDU@ aPPHÃ 7G68F H6BI@UD8 T@ITPST `@GGPXÃ XCDU@ 96SFÃBS@@I TUSP7@ `@GGPX ASPHÃE' Q6IÃÉÃUDGU 8PGPVSÃXC@@G WDPG@U QDIF @AA@8UT ASPHÃE BS@` Q6IÃÉÃUDGU GDBCUÃBS@@I "ÃW98 S@9 H6B@IU6Ã GDBCUÃ7GV@ 8`6I 7G68F BPG9 A6IÃ %/$&. aPPHÃ! A6IÃ! %/$&. 7GV@...
- Page 28 Ã Ã %Ã9DTQG6`Ã86S9 ASPHÃE# 'ÃHPUPS Ã Ã ! Ã B Ã U Ã &1 &1 &1 &1 &1 &1 &1 &1 8PI@8UPSÃS@G6`Ã86S9 &1 &1 &1 &1 Ã ! Ã Ã U Q6IÃÉÃUDGUÃ86S9 UDGU "ÃW98 XCDU@ 7SPXI 7G68F S@9 XCDU@ @I8P9@SÃQ6I S@9 @I8P9@SÃUDGU PS6IB@...
Need help?
Do you have a question about the XR7 WASH and is the answer not in the manual?
Questions and answers