Contents Of Mail Sent; Adjust Clock Page - Panasonic PT-DW5000UL Operating Instructions Manual

Using Web Browser Control

Contents of mail sent

• Mail with the contents shown below is sent when the E-mail
settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type
----- E-mail setup data -----
TEMPERATURE WARNING SETUP
MINIMUM TIME
INPUT AIR TEMPERATURE Over [ 45C / 113F ]
ERROR
LAMP1 RUNTIME
LAMP1 RUNTIME
LAMP2 RUNTIME
LAMP2 RUNTIME
INPUT AIR TEMPERATURE
PERIODIC REPORT
Sunday [ ON ] Monday [ OFF ] Tuesday [ ON ] Wednesday [ OFF ]
Thursday [ ON ] Friday
00:00 [ ON ]
04:00 [ OFF ] 05:00 [ ON ]
08:00 [ ON ]
12:00 [ OFF ] 13:00 [ ON ]
16:00 [ ON ]
20:00 [ OFF ] 21:00 [ ON ]
----- check system -----
MAIN CPU BUS
FAN
OPTICS MODULE TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP TEMPERATURE
LAMP2 REMAIN TIME
LAMP1 REMAIN TIME
•
•
•

Adjust clock page

Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• If the time becomes incorrect immediately after setting the correct time, then the battery needs to
Note
be changed. Contact the dealer where you bought the projector to have the battery changed.
52
: D5600
at [ 60] minutes interval
[ ON ]
[ ON ] at REMAIN [ 100] H
[ ON ] at REMAIN [ 200] H
[ ON ] at REMAIN [ 300] H
[ ON ] at REMAIN [ 400] H
[ OFF ]
[ OFF ] Saturday [ ON ]
01:00 [ OFF ] 02:00 [ ON ] 03:00 [ OFF ]
06:00 [ OFF ] 07:00 [ ON ]
09:00 [ OFF ] 10:00 [ ON ] 11:00 [ OFF ]
14:00 [ OFF ] 15:00 [ ON ]
17:00 [ OFF ] 18:00 [ ON ] 19:00 [ OFF ]
22:00 [ OFF ] 23:00 [ ON ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
• Mail with the contents shown below is sent
when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Type : D5600
––––– check system –––––
MAIN CPU BUS
FAN
OPTICS MODULE TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP TEMPERATURE
LAMP2 REMAIN TIME
LAMP1 REMAIN TIME
LAMP2 STATUS
LAMP1 STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP TEMP.SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
(Error code 00 10 00 00 00 00 00 00)
Input air temperature
Optics module temperature : 30 degC / 86 degF
Around lamp temperature
SET RUNTIME 30 H
POWER ON 33 times
LAMP1 ON 34 times
LAMP1 LOW 25 H
LAMP1 HIGH 5 H
LAMP2 ON 24 times
LAMP2 LOW 16 H
LAMP2 HIGH 4 H
LAMP1 REMAIN 1476 H
LAMP2 REMAIN 1484 H
----- Network configuration -----
IP address 192.168.0.8
MAC address 00:00:00:00:00:00
Thu Mar 02 14:11:02 2006
----- Memo -----
Time zone selection
Button to update time zone setting
New date field
Button to update time and date
settings
New time field
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ FAILED ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
[ OK ]
: 30 degC / 86 degF
: 37 degC / 98 degF