Download Print this page

Phonic MAX 2500 plus User Manual

Power amplifier
Hide thumbs

Advertisement

MAX 860
MAX 1500
MAX 2500
POWER AMPLIFIER
AMPLIFICADOR POTENCIADO
功率放大器
MAX 2500 Plus
User's Manual

Manual del Usuario

使用手册

Advertisement

loading

  Also See for Phonic MAX 2500 plus

  Summary of Contents for Phonic MAX 2500 plus

  • Page 1: Manual Del Usuario

    MAX 860 MAX 1500 MAX 2500 POWER AMPLIFIER AMPLIFICADOR POTENCIADO 功率放大器 MAX 2500 Plus User’s Manual Manual del Usuario 使用手册...
  • Page 2: Table Of Contents

    ESPECIFICACIONES ......18 Phonic preserves the right to improve or alter any information within this document without prior notice Phonic se reserva el derecho de mejorar o alterar cualquier información provista dentro de este documento sin previo aviso PHONIC保留不预先通知即可更新本文件权利 V1.1 05/13/2009...
  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS The apparatus shall not be exposed to dripping or splashing and that no objects with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.
  • Page 4: Introduction

    ● Output: 300W for MAX 860 Plus, 450W for MAX with 4 rack-mount screws and cup washers. In gen- 1500 Plus and 750W for MAX 2500 Plus, all at eral, power amplifiers usually are heavier than any 4 ohms other audio equipment, so when installing this unit ●...
  • Page 5: Connections

    1. HEAT VENTILATION This unit comes with variable speed fan that auto-adjusts fan speed depending on the temperature of the machine during operation. Be sure not to obstruct the heat vents in any way. This will ensure the amplifier is always properly ventilated.
  • Page 6: Operation

    OPERATION REAR PANEL 9. Grounding/Floating Switch FRONT PANEL This switch allows the circuit and chassis grounds to be 4. POWER SWITCH separated in case of a ground conflict. In normal use the This switch turns the power of the unit on. Remember to switch should be in the Ground On position.
  • Page 7 PARALLEL When set to PARALLEL mode, the input signal of Channel 2 parallels the input signal of Channel 1, so only one input jack is needed for the signal source. Even though the input signal of both channels parallels each other, the output level of each channel is determined by its own independent gain controls.
  • Page 8 BRIDGE MONO This mode is for those who need high level output. It combines the power of both channels to produce the maximum amount of power the unit can handle. Make sure your speaker can handle higher wattage this mode offers. Remember, the minimum impedance requirement is 4 ohm.
  • Page 9: Protection

    PROTECTION 10. CHASSIS GROUNDING CONNECTING POINT To avoid the possibility of ground loop, this unit comes with The unit comes with many circuitry protection features for chassis grounding point allowing it to be connected to other preventing it and speakers it’s connected to from harm. units for sharing a common grounding.
  • Page 10: Specifications

    SPECIFICATIONS MAX 860 Plus MAX 1500 Plus MAX 2500 Plus Stereo Mode (driving both channels) Continuous Average Output Power Per Channel 8Ω EIA 1kHz 0.1%THD 200W 280W 500W 4Ω EIA 1kHz 0.1%THD 300W 450W 750W Bridge Mono Mode Continuous Average Output Power 8Ω...
  • Page 11 Phonic visite nuestra página Phonic distributor. For a list of Phonic web en www.phonic.com y entre a la sección Get www.phonic.com Get Gear distributors please visit our website at Gear. También, puede ponerse en contacto directa- www.phonic.com and click on Get Gear.

This manual is also suitable for:

Max 860 plusMax 1500 plus