Input/Output Connections; Playback On A Conventional Tv; Rf Unit Connections - Sony AV-3600 Service Manual

the
monitor
screen,
push
the
AUDIO DUB
switch
down. Sound dubbing
will start.
4.
At the end
of
the
dub,
set
the
Function Lever to
STOP.
Playback
on a Conventional
TV
A
conventional
TV
receiver
can
also
be used for
playback
display
by
adapting the
RF
Unit
(optional)
to
the
Videocorder.
1.
Remove the cover of the
RF
Unit
compartment.
2.
Insert
the
RF
Unit
(RFU-53W
or
54W
whichever
channel
is
inactive in
your
area) into
the
com-
partment and connect
the Videocorder,
Antenna
Selector
and
TV
receiver as
shown
in Fig.
1-1.
w
antenna selector
4
A
V-3600
\
to
[RF OUT]
n
to
antenna
terminals
J
©
Fig. 1-1.
RF
Unit connections
3.
Set
the
ANT/VTR
switch
on
the
Antenna
Selector
to
VTR.
4.
Set the
TV
channel selector
to the channel to
which
the
RF
Unit
is
set.
5.
Set the
Videocorder to the
playback mode.
6.
Adjust
the
fine
tuning
knob
for the best picture.
1-4.
INPUT/OUTPUT
CONNECTIONS
Figure 1-2
shows
all
input
and output
terminals,
and
output-signal characteristics.
Normal
connections
to the
monitor
are
made
at
8-pin jack
marked TV.
Normal camera connections
are
made
at
the 6-pin
CAMERA
receptacle. Signal
and
power
connections
to
other accessory
equipment
are as
shown.
A.
Power Cord Receptacle
[AC IN
117V
60 Hz].
Connects
to a three-wire (parallel-ground) ac
receptacle.
B.
Power Output
Receptacle,
unswitched
[AC
OUT
1
17V 500W]
.
Line output
to
power
a
monitor
or
camera.
Max.
rating
500
watts.
C.
TV-Monitor
Jack
[TV]
.
Provides
all
signal
con-
nections to
and from the monitor. See
detail.
D.
Fuse
[1.5 A] Contains a
1.5-ampere
fuse.
E.
Audio
Out
Jack
[LINE
OUT]
.
Provides an addi-
tional
audio-output feed
to
supply playback
monitors or other audio
components.
Signal
level:
dB
(0.775
V)
across
high impedance. This
jack
is
in
parallel
with
pins
1
and
5 (5
grounded)
of the
TV
jack.
F. Auxiliary Input Jack
[AUX.
IN].
Provides
an
alternative
audio input
for high
impedance micro-
phones, studio feeds,
record
players,
and
other
audio
sources. Signal level
requirements: -20
dB
across
high impedance.
G.
Microphone Input Jack
[MIC IN]. Signal feed
point for a
SONY
microphone or other micro-
phone
with similar characteristics. Signal level re-
quirements: -60 dB, 600 ohms,
single
ended.
H.
Camera
Jack
[CAMERA].
Provides video
and
sync connections
to
the camera. See
detail.
I.
UHF
Input Connector
[VIDEO
IN]. Pro\ides
video input
connection
for
a
camera
or
TV
monitor equipped
a
video-output
UHF
con-
nector.
J.
UHF
Output Connector
[VIDEO
IN]. Pro-
vides
an additional
video-output feed to supply
a
monitor having a video-input
UHF
connector.
K.
RF
Output
Jack
[RF OUT].
Supplies output
to the antenna terminals of a conventional
TV
receiver
when
the
RF
unit
is
used.
L.
RF
Unit
Compartment
[RF UNIT].
The
RF
Unit (optional)
is
inserted into this
com-
partment.
1-3