Shure se112 User Manual

SHU
Wearing the Earphones
The following are some suggested ways of wearing
the earphones.
Inserting the Earphones
Insert the earphones so they form a tight seal. The fit
of the earphone can greatly affect sound quality.
Important: If there seems to be a lack of low
frequency response (bass), this means that the
earphone sleeve is not forming a tight seal. Gently
push the earphone deeper into the ear canal or try a
different sleeve.
Warning:
Do not push the earphone sleeve beyond
the ear canal opening.
Removing the Earphones
Grasp the body of earphone and gently twist to
remove.
Note:
Do not pull on cable to remove earphone.
©2013 Shure Incorporated
27A22882 (Rev. 1)
®
SE112
Sound Isolating™ Earphones
Changing Sleeves
Twist and pull to remove the sleeve from the
nozzle.
Slide on a new sleeve so that it completely covers
the barb and the nozzle.
Caution:
If the barb or any of the nozzle is exposed,
the sleeve is not properly installed. Replace sleeves if
they do not tightly grip the nozzle. To ensure proper fit
and performance, use only sleeves supplied by Shure
(unless using custom molded sleeves).
Choosing a Sleeve
Soft flex sleeves are included in small, medium, and
large sizes. Select an earphone sleeve that provides
the best fit and sound isolation. It should be easy to
insert, fit comfortably, and easy to remove.
Soft Flex Sleeves
Using the Remote (m+ models
only)
Use the remote to control compatible media phone
players.
~
Play music Click the center button once
Pause music Click the center button
once.
Change volume
Click the volume up ( +) or
volume down (-) button to
increase or decrease the
volume.
Go to next track Double-click the center
button.
Go to previous
Triple-click the center
track
button.
Restart current Triple-click after 6 seconds.
track
Fast-forward
Double-click and hold the
center button.
Send/End Call Click the center button
once.
For more information about compatible models go to:
www.shure.com
Cleaning the Nozzle
If you notice a change in sound quality, remove the
sleeve and check the nozzle of your earphone. If
nozzle is blocked, clear obstruction by using wire
loop end of cleaning tool.
Nozzle Cleaning Tool
Warning:
The cleaning tool is only to be used to
clean the earphones. Any other use, such as using
the tool to clean ears, could result in injury.
Maintenance and Cleaning
Careful maintenance ensures a tight seal between
the sleeve and nozzle, improving sound quality and
product safety.
Keep the earphones and sleeves as clean and
dry as possible.
To clean sleeves, remove them from
earphones, gently rinse in warm water and air
dry. Foam sleeves require a longer drying time.
Inspect for damage and replace if necessary.
Ear sleeves must be completely dry before
reusing.
Wipe the earphones and sleeves with mild
antiseptic to avoid infections. Do not use
alcohol-based disinfectants.
Do not expose earphones to extreme
temperatures.
Replace sleeves if they do not fit properly.
Do not attempt to modify this product. Doing
so will void the warranty and could result in
personal injury and/or product failure.
Accessories
For information about earphone accessories and
other Shure products visit:
www.shure.com
Furnished accessories subject to change.
Certifications
This product meets the Essential Requirements of
all relevant European directives and is eligible for
CE marking.
The CE Declaration of Conformity can be obtained
from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: EMEAsupport@shure.de
fa
!
~ri~d
in China