1. Manuals
  2. Brands
  3. Vicon Manuals
  4. Camera Lens
  5. V8-80HS-1 series
  6. Installation & operation manual

Vicon V8-80HS-1 series Installation & Operation Manual

High-speed motorized zoom lenses
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
V8-80HS-1 SERIES OF HIGH-SPEED
Copyright © 2000 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com
Vicon part number 8006-8684-02-00
MOTORIZED ZOOM LENSES
X684
Section 15 Rev 100

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V8-80HS-1 series and is the answer not in the manual?

Questions and answers

Related Manuals for Vicon V8-80HS-1 series

Summary of Contents for Vicon V8-80HS-1 series

  • Page 1 Copyright © 2000 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com...
  • Page 5 Introduction The information in this manual covers the installation, operation and maintenance of the V8-80HS-1 Series of High-Speed Motorized Zoom Lenses. These units should be installed by a qualified technician using approved materials in conformance with national, state and local electrical codes. Read these instructions through completely before attempting installation.
  • Page 6 Notes 2 • • Introduction X684 Rev 100 V8-80HS-1 Zoom Lenses...

  • Page 7: Installation

    Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition as it left the factory. Inspect the cartons upon delivery and, if damage is present, make detailed notes on the carrier’s bill. Then obtain the carrier’s agent signature and file a damage claim as soon as possible.
  • Page 8 Table 2 Table 3 Wiring for M and MS Lenses Wiring for M and MS Lenses with Presets Pin Number Wire Color Function Pin Number Wire Color Function White Iris drive White Iris drive Zoom drive Zoom drive Green Focus drive Green Focus drive Black...
  • Page 9 Wiring the Autoiris (AC) Lens AC lenses have two cables. One cable has a AMP MR (Miniature Rectangle) connector. This provides connection for the zoom, focus and preset controls. Lenses without the preset function are supplied with a 6-pin connector, while lenses with presets have a 9-pin connector. The wiring of both connectors is shown in Figure 2. Table 4 shows the color-coding of the control cables and Table 5 shows the color coding for the control and preset cables.

  • Page 10: Autoiris Adjustment

    Black Ground Zoom and Focus Adjustment Procedure The following procedure should be used to obtain the best results in setting optical and mechanical focus. 1. Adjust the zoom function to the maximum telephoto setting, then focus on a convenient distant object. Readjust the zoom to the maximum wide angle setting and check the focus.
  • Page 11 little at a time. If the contrast is too strong, turn the potentiometer clockwise, toward P; if the contrast is too weak, turn the potentiometer counterclockwise, toward A. Video Level (LEVEL) The level control is preset at the factory for optimum performance, so normally no adjustment is required. Adjusting this control when it is not necessary may spoil the picture quality.

  • Page 12: Shipping Instructions

    Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A.

  • Page 13: Technical Information

    Zoom and focus: 43 mA max. per motor. Connectors: Iris: 3-conductor shielded pendant cable supplied for iris. Zoom and focus: Standard lens; Vicon part number 8000-9800-00 on pendant cable. (Mating connector 8000-9736-00 supplied.) Preset lens; Vicon part number 8000-9801-00 on pendant cable.
  • Page 14 Cable Requirements: Without presets: 3 conductor, shielded. With presets: 7 conductor, shielded. Video: Requires video from 0.5 V to 1.0 V peak-to-peak for proper iris operation. OPERATIONAL Duty Cycle: Intermittent. Iris Speed: M, MS Lens: 1.5 – 8 sec at 8 VDC, adjustable. AC Lens: 2.0 sec, not adjustable.

Table of Contents