Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Huntcctv HTP-T13MG28D
Summary of Contents for Huntcctv HTP-T13MG28D
- Page 1 HTP‐T13MG28D H.264 IP DOME CAMERA User Manual Ver. 1.0...
-
Page 2: Safety Precaution
We appreciate your purchasing HTP-T13MG28D. Before installing the product, please read the following with care. Make sure to turn off the power before installing HTP-T13MG28D. Do not install under the direct sunlight or in dusty areas. Make sure you use the product within the temperature and humidity specified in the specification. -
Page 3: Table Of Contents
Remote Video Monitoring ...................... 9 2. Initialization of IP Address ....................... 11 4. Remote Configuration........................12 1. Using Remote Configuration ....................12 2. HTP-T13MG28D Setup ......................13 2.1 System ........................... 13 2.2 Video..........................15 2.3 Audio ..........................18 2.4 Network .......................... 19 2.5 Serial Port Configuration .................... -
Page 4: Introduction
1. About User Manual The User Manual is provided to advise how to use this premium network camera, HTP-T13MG28D. This manual includes how to trouble shoot in case of problems as well as installation, operation and setting up the HTP- T13MG28D. -
Page 5: Product And Accessories
HTP-T13MG28D User Manual Sensor & Alarm Support direct connections of external sensor and alarm devices. Event alarm User Interface Diagnose and upgrade through dedicated program called True Manager System configuration using Internet Explorer High Reliability Embedded system System recovery by dual Watch-dog functions 3. -
Page 6: Rotation Functions
PC client or a decoder system or 1 to many connections where one HTP-T13MG28D can be connected several PCs and decoder systems. Topology Generally HTP-T13MG28D and a PC or a decoder are connected in a 1 to 1 mode or a 1 to many configuration. 1:1 connection Remote Center... - Page 7 HTP-T13MG28D User Manual One HTP-T13MG28D is installed at a site where video images are transmitted. A PC or a decoder is installed at a central location to receive and view the video images on an analog monitor. Audio and serial data are transferredin either direction.
-
Page 8: Installation
PT commands to the external equipment via the serial port. When a decoder system instead of PC client is connected to HTP-T13MG28D, the serial port and that of the decoder system works in pass-through mode. That is, data from at one port is delivered to the other port, vice versa . -
Page 9: Connecting Power
HTP-T13MG28D User Manual 5. Connecting Power After confirming the power source, connect power adaptor and then 12V DC connector to the system. 6. Checking Operating Once the power is supplied to the camera, it will start booting. The system will boot up to an operating mode after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the system is ready. -
Page 10: System Operation
Default ID : admin Password : 1234 Video Monitoring via Decoder System Once the HTP-T13MG28D’s IP address is set in the remote IP address section of the decoder, the decoder system will connect to the HTP-T13MG28D and start receiving the video images. - Page 11 Focus Near, Focus Far, Auto Focus djust the focus Sensor Input When the sensor on the HTP-T13MG28D is connected and working, the light turns red. Alarm Output Alarm Output button can trigger an event directly from the Live View page.
-
Page 12: Initialization Of Ip Address
HTP-T13MG28D User Manual 2. Initialization of IP Address If HTP-T13MG28D’s IP address is lost, the HTP-T13MG28D can be reset. Press a reset button on the back of the HTP-T13MG28D, this will reset the camera to factory defaults as follows: While the system is in operation, press the reset button for more than 5 seconds. -
Page 13: Remote Configuration
1. Using Remote Configuration Remote setting is available by using web browser. Enter the IP address of HTP-T13MG28D and then live view screen appears as below. Press Setup button located in the upper right area of the monitoring screen to go to the server setup. -
Page 14: Htp-T13Mg28D Setup
HTP-T13MG28D User Manual 2. HTP-T13MG28D Setup 2.1 System -13-... - Page 15 Do not press the Reboot button unless the server needs a reboot . Factory Reset Current IP Address of HTP-T13MG28D is changed to default IP Address, 192.168.10.100. System log and user registrations are also cleared. The other setting value will be remained.
-
Page 16: Video
HTP-T13MG28D User Manual 2.2 Video -15-... - Page 17 HTP-T13MG28D User Manual - ENCODE Enable Preview Turn on to transmit the video direct to HD monitor and select the one of Output Formats in the end of the Video setting section. *Scaling: If the encoding resolution was different from the input resolution, encoding video was cropped.
- Page 18 HTP-T13MG28D User Manual - DUAL ENCODE Use Dual Encode Select On to use dual encode Dual Encode Algorithm H.264 and MJPEG can be selected for secondary streaming. Maximum resolution is 720 x 480 and there are 8 steps of resolution. If MJPEG is selected, Preference supports only Quality mode.
-
Page 19: Audio
HTP-T13MG28D User Manual Sensitivity A condition to trigger an event of motion detection. The value determines the sensitivity of the motion detection within a block: the smaller, the more sensitive. It is selectable from from 0 to 10. Information Display System ID and/or server time can be display over the video window in Web View. -
Page 20: Network
HTP-T13MG28D User Manual 2.4 Network -19-... - Page 21 RTSP port used for RTSP-based connection SNMP HTP-T13MG28D can be used as an SNMP agent. It is compatible to both SNMPv1 and SNMPv2c. Vender specific MIBs for IP camera/server are defined. SNMP listen port can be set and disabled when it is 0.
- Page 22 HTP-T13MG28D User Manual Select the DDNS(Dynamic DNS) server to use. One of the two servers can be selected. - TrueDNS : use TrueDNS service. Systems can be registered on the website for TrueDNS service: http://ns1.truecam.net. System will get a domain name of xxx.truecam.net style. Refer to the user guide document for True DNS service.
-
Page 23: Serial Port Configuration
HTP-T13MG28D User Manual 2.5 Serial Port Configuration Serial Port Configuration There is one serial port, RS-485 in HTP-T13MG28D. The serial port can be configured as follows Mode Selection Bitrate 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps Data Bits 5, 6, 7, 8 bits... - Page 24 Select the serial port used for PTZ camera control. Direct Keyboard Control Keyboard controller can be connected to HTP-T13MG28D directly to control zoom and focus. Sensor Type There is one sensor input port on HTP-T13MG28D. The sensor port can be configured to the following. Function Operation Not used...
-
Page 25: Event Configuration
HTP-T13MG28D User Manual 2.6 Event Configuration -24-... - Page 26 HTP-T13MG28D User Manual The HTP-T13MG28D has one sensor port and one alarm port. When a decoder system instead of a PC client is connected to a HTP-T13MG28D, one system becomes a Local system and the other a Remote system (Generally a system which is being used by the user is called as Local system). Then, actions for events can be configured for events from the remote system as well as for local system.
- Page 27 HTP-T13MG28D User Manual needs to be specified on Server Address field, and Port specifies the port for SMTP operation (Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly).
-
Page 28: Preset
Press Set Button Save This function is only available when a PTZ receiver is used with HTP-T13MG28D. Configure up to 15 preset positions. Preset function is not available on some PTZ receivers. Make sure to check if a PTZ receiver supports preset. -
Page 29: User
HTP-T13MG28D User Manual 2.8 User User can be registered and privilege level of a user can be specified. User configuration is allowed only to admin user. Max 16 users can be registered and each user can have one of four privileges. - Page 30 HTP-T13MG28D User Manual Change Password Pressing Modify Password button after selecting a user shows a page for changing password. In case changing admin password, old password is checked. Modify Privilege Level Pressing Modify Privilege button after selecting a user shows a page for changing the privilege. It is not allowed to change the privilege level of admin user.
-
Page 31: Camera
HTP-T13MG28D User Manual 2.9 Camera AE Operation Mechanical Iris Lens Fixed Iris Lens or DC Iris Lens can be selectable. Slow Shutter Shutter speed can be adjusted to be slow Flickerless Reduce the influences from flickers of fluorescent lights with 50/60Hz. - Page 32 HTP-T13MG28D User Manual Max AGC Gain Auto Gain Control can be adjusted Digital Day & Night Digital Day & Night function is supported. AWB Operaiton AWB Operation Performs white balance control that fit to the light sources. -31-...
-
Page 33: Appendix : Poe Specification
HTP-T13MG28D User Manual 5. APPENDIX : PoE Specification IEEE802.3af compliant Output Voltage : 12.0V Input voltage range : 36V to 57V 1500V isolation (input to output) PoE must be protected from over-voltages exceeding the 80V maximum rated surge input voltage...
Need help?
Do you have a question about the HTP-T13MG28D and is the answer not in the manual?
Questions and answers