Panasonic HDX900 Operating Instructions Manual page 99

Table of Contents

Advertisement

Chapter 6 Maintenance and inspections
6. SERVO
Indications on LCD
screen
WARNING lamp
Tally lamp
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
7. RF
Indications on LCD
screen
WARNING lamp
Tally lamp
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
8. WIRELESS RF
Indications on LCD
screen
WARNING lamp
Tally lamp
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
Downloaded From CamcorderManual.com Panasonic Manuals
"SERVO" display lights (during recording and
playback).
Flashes four times a second (during recording
and playback).
Flashes four times a second (during recording
and playback).
"SERVO" display lights (during recording and
playback).
Sounds four times a second (during recording
and playback).
The servo is disturbed.
Operation continues but the unit may not operate
correctly.
Turn off the power and consult your dealer. The
warning display may flash for a moment and then
disappear when tape transport commences: this
is normal and not indicative of a failure or
malfunctioning.
"RF" display flashes (during standby and
recording).
Flashes four times a second (during recording).
Flashes four times a second (during recording).
"RF" display lights (during recording).
Sounds four times a second (during recording).
The video heads have become clogged. There
is a problem in the video system.
The cleaning rollers are activated to clean the
heads (for a maximum of 3 seconds).
Recording continues but the signals may not be
recorded correctly.
The indications on LCD screen are retained until
the REC/PAUSE status is established. They go
off as soon as the unit transfers from the
REC/PAUSE mode to another mode.
Clean the heads.
If the signals cannot be
recorded correctly even after cleaning, consult
your dealer.
No indication
Flashes four times a second (during standby and
recording).
Flashes four times a second (during recording).
"WIRELESS RF" display lights for at least 3
seconds during recording.
Sounds four times a second (for at least 3
seconds during standby and recording).
Poor wireless signal reception.
Operation continues but the signals from the
wireless microphone cannot be received.
Check the microphone's power supply and the
reception condition of the receiver.
(continued)
9. BATTERY NEAR END
Indications on LCD
The bar display that shows the remaining battery
screen
charge starts flashing.
WARNING lamp
Flashes once a second.
Tally lamp
Flashes once a second.
Viewfinder
BATT LED starts flashing.
Alarm
Sounds four times a second.
Warning description
The battery charge is nearly depleted.
VTR unit operation
Operation continues.
Corrective action
Replace the battery when it becomes necessary.
10. TAPE NEAR END
Indications on LCD
The bar display that shows the remaining tape
screen
amount starts flashing.
WARNING lamp
Flashes once a second (during recording).
Tally lamp
Flashes once a second (during recording).
Viewfinder
≥ The remaining tape display starts flashing (in
the EE mode).
≥ " = " flashes for 3 seconds one minute before
the tape reaches the end.
Alarm
Sounds once a second.
Warning description
The tape is close to its end (about 2 minutes
remain).
VTR unit operation
Operation continues.
Corrective action
Replace the cassette tape when it becomes
necessary.
11. 1394
Indications on LCD
"1394 E-22" display flashes.
screen
WARNING lamp
Flashes four times a second.
Tally lamp
Flashes four times a second.
Viewfinder
When error code 92 appears, "1394 INITIAL
ERROR" display lights (during standby).
Alarm
Sounds four times a second.
Warning description
There is something wrong with the signals
supplied to the DVCPRO connector.
VTR unit operation
Operation continues, but something is wrong with
the signals supplied to the DVCPRO connector.
Corrective action
Check the IEEE 1394 cable and DVCPRO
connector connections and the settings of the
external units or menu settings, and then turn the
power off and back on.
If the warning display is not cleared, check "6-3-2
Error codes," and consult your dealer.
6
99

Advertisement

Table of Contents
loading

This manual is also suitable for:

Aj-hdx900

Table of Contents