Subscribe to Our Youtube Channel
Related Manuals for HERKULES H-BW 600
Summary of Contents for HERKULES H-BW 600
- Page 1 TE-AG 180 Original operating instructions Angle grinder - . t : . r - . I : . r Anl_TE_AG_230_SPK1.indb 1 07.09.12 13:59...
- Page 2 - 2 - Anl_TE_AG_230_SPK1.indb 2 Anl_TE_AG_230_SPK1.indb 2 07.09.12 13:59 07.09.12 13:59...
- Page 3 - 3 - Anl_TE_AG_230_SPK1.indb 3 07.09.12 13:59...
- Page 4 - 4 - Anl_TE_AG_230_SPK1.indb 4 Anl_TE_AG_230_SPK1.indb 4 07.09.12 13:59 07.09.12 13:59...
- Page 5 Table of contents 1. Safety information 2. Layout and items supplied (Figure 1) 3. Proper use 4. Technical data 5. Before starting the equipment 6. Operation 7. Replacing the power cable 8. Cleaning, maintenance and ordering of spare parts 9. Disposal and recycling 10.
- Page 6 “ n i t ” y Wear ear-muff s. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Wear safety goggles.
-
Page 7: Safety Information
• i l l e i l Important! Inspect the equipment and accessories for transport damage. must be observed to avoid injuries and damage. • , e l l i t Please read the complete operating manual with the end of the guarantee period. due care. -
Page 8: Before Starting The Equipment
Sound and vibration Residual risks Even if you use this electric power tool in Sound and vibration values were measured in accordance with instructions, certain resi- accordance with EN 60745. dual risks cannot be rules out. The following hazards may arise in connection with the LpA sound pressure level .... -
Page 9: Operation
thick, screw on the ange nut with the at side Take care that the safety device is secure. facing the grinding or cutting wheel. Never use the angle grinder without the guard. 6.3 Flange arrangements when using grin- ding wheels and cutting wheels (Fig. 5.3 Test run for new grinding Wheels 7-10) Allow the right-angle grinder to run in idle for at... -
Page 10: Replacing The Power Cable
6.6 Operating Modes tack the plastic parts of the equipment. Ensu- re that no water can seep into the device. The 6.6.1 Rough grinding (Fig. 11) ingress of water into an electric tool increases the risk of an electric shock. Caution: Use the safety device for san- ding/grinding (included in items supplied). - Page 11 Warranty provisions Einhell Australia replacement of the equipment in accordance with the overview below. Statutory guarantee claims are unaffected. Defect with regard to material or 24 months construction Wear parts* Carbon brushes 6 months Consumables* Cutting wheels, grinding wheels Warranty only in case of an im- mediate defect (24 hours after purchase / date on the bill) * Not necessarily included in the scope of delivery!
-
Page 12: Guarantee Certificate
The guarantee provided in this Guarantee Certificate is given by Einhell Australia Pty Limited ACN 134 632 858 of 6/166 Wellington Street, Collingwood, Victoria (Telephone number 1300 922 271) (Einhell Express Guarantee). CERTIFICATE GUARANTEE Dear Customer, All of our products undergo strict quality checks. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee certificate.
Need help?
Do you have a question about the H-BW 600 and is the answer not in the manual?
Questions and answers