Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Luxman SQ-N100
Summary of Contents for Luxman SQ-N100
- Page 1 VACUUM TUBE INTEGRATED AMPLIFIER SQ-N100 Owner`s Manual...
-
Page 2: Table Of Contents
Luxman and its working staff are happy to have such a great opportunity that you have selected our Luxman products by virtue of a profound lot and that both of us can have the same emotions and values in regard to audio matters and music. -
Page 3: Precautions
The AC outlet power of this unit where you bought the unit or any is 200W at maximum. The total switches of this unit and all other nearby Luxman Service Center. consumption power for units to connected units. Otherwise, a be connected shall not exceed... -
Page 4: Names And Functions Of Parts
Names and Functions of Parts Front panel 1. Power switch (POWER) 5. Volume control indicator This switch turns the power This indicator is an index for the supply ON/OFF. When the I/O sound level. terminals are connected, turn This indicator blinks in the mid- off this switch without fail. - Page 5 Names and Functions of Parts Top panel 8. Tone control quency characteristics 10. Vacuum tube cover are obtained. Turning it (TONE CONTROL, bass, This cover is used for the pro- clockwise causes the tection of vacuum tubes. For treble) high-frequency range safety, this cover should be left bass: This is a level control...
-
Page 6: Volume Control Indicator
Names and Functions of Parts Remote controller (RA-N2) Remote control The remote control can be used by pointing it at the remote control infrared receiver of this unit. It should be used within the range shown in the illustration. 30° 30°... - Page 7 Names and Functions of Parts Rear panel 18. AC outlet (UNSWITCHED) 13. Signal ground terminal 16. Speaker output terminal This is an auxiliary power outlet (SIGNAL GROUND) (SPEAKERS) to feed power to other equip- This is a signal ground terminal This terminal is used for the ment.
-
Page 8: Connections
Connections Before Making Connections Connecting a record player Before connecting other devices, Connect between the output termi- connect the jack side (where three nal of an analog record player and holes are provided) of the acces- the PHONO terminal of this unit sory power cable to the AC inlet of through two pin-plug cables of R this unit. -
Page 9: Connection Diagram
Connection diagram RECORD PLAYER CD PLAYER – – SPEAKER SYSTEM... -
Page 10: Operation
Operation Before operation Operation with tone control 1. Confirm that the connections function are correct. (Normal playback The tone control function of this cannot be achieved with wrong unit comes in low (bass) and high connections for R, L, , and level controls (treble). -
Page 11: Sq-N100 Block Diagram
SQ-N100 Block Diagram... -
Page 12: Specifications
Specifications Rated output 12W + 12W (6Ω), 10W + 10W (8Ω, 4Ω) Input sensitivity LINE: 150mV, PHONO (MM): 2.2mV Input impedance 47KΩ Frequency response 20Hz – 50KHz (within –3 dB) Total harmonic distortion 0.3% or less (1 kHz rated output) S/N ratio 90dB or more Input... -
Page 13: After-Sales Services And Quality Assurance
After-sales services and quality assurance The Luxman products have passed a variety of rigorous checks throughout the manufacturing processes from the selection of each part to shipment. Careful quality control is carried out at all times. If this unit should cause a problem, please contact our Service Center or the store where you bought the unit. -
Page 14: Troubleshooting
Troubleshooting If you encounter a problem during use, check the following checklist and instruction manuals of the other components before suspecting a fault and sending your unit in for repairs. Problem Cause Solution No power is sup- • The power plug is disconnected from •... - Page 15 MEMO...
- Page 16 AG00987CXXA LUXMAN CORPORATION, JAPAN...
Need help?
Do you have a question about the SQ-N100 and is the answer not in the manual?
Questions and answers