Download  Print this page

Pioneer deh-p980bt Service Manual

Multi-cd control dsp high power cd/mp3/wma/aac player with bluetooth wireless technology and fm/am tuner.
Hide thumbs

Advertisement

QQ
3 7 63 1515 0
MULTI-CD CONTROL DSP HIGH POWER CD/MP3/WMA/AAC PLAYER
WITH BLUETOOTH WIRELESS TECHNOLOGY AND FM/AM TUNER
DEH-P980BT
DEH-P9800BT
DEH-P9850BT
This service manual should be used together with the following manual(s):
TE
L 13942296513
Model No.
CX-3164
CRT3583
www
For details, refer to "Important Check Points for Good Servicing".
.
PIONEER CORPORATION
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
http://www.xiaoyu163.com
Order No.
Mech.Module
S10.5COMP1
x
ao
u163
y
i
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
http://www.xiaoyu163.com
2 9
8
DEH-P980BT/XN/UC
/XN/UC
/XN/ES
Q Q
3
6 7
1 3
1 5
CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
co
.
9 4
2 8
ORDER NO.
CRT3687
/XN/UC
0 5
8
2 9
9 4
2 8
Remarks
m
K-ZZD.MAY 2006 Printed in Japan
9 9
9 9

Advertisement

Table of Contents

   Related Manuals for Pioneer deh-p980bt

   Summary of Contents for Pioneer deh-p980bt

  • Page 1 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2006 K-ZZD.MAY 2006 Printed in Japan...
  • Page 2: Safety Information

    (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 3 To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 4: Table Of Contents

    6.8 BLUETOOTH TEST MODE........................84 L 13942296513 7. GENERAL INFORMATION ..........................89 7.1 DIAGNOSIS ............................. 89 7.1.1 DISASSEMBLY ............................. 89 7.1.2 CONNECTOR FUNCTION DESCRIPTION ..................94 7.2 IC ................................95 7.3 OPERATIONAL FLOW CHART ......................115 8. OPERATIONS .............................. 116 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 5: Specifications

    1. SPECIFICATIONS 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 6 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 7 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 8: Exploded Views And Parts List

    • Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 2.1 PACKING L 13942296513 16 16 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 9 Protector XHP7008 Screw CBA1650 Polyethylene Bag CEG-127 Protector XHP7007 Screw CRZ50P090FTC (2) CONTRAST TABLE DEH-P980BT/XN/UC, DEH-P9800BT/XN/UC and DEH-P9850BT/XN/ES are constructed the same except for the following: Mark Description DEH-P980BT/XN/UC DEH-P9800BT/XN/UC DEH-P9850BT/XN/ES Not used Not used ARY1048 Not used Owner's Manual...
  • Page 10: Exterior(1)

    2.2 EXTERIOR(1) 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 11 Insulator CNN1327 Lighting Conductor CNV9011 Lighting Conductor CNV9013 Cushion CNN1405 Cable CDE8057 (2) CONTRAST TABLE DEH-P980BT/XN/UC, DEH-P9800BT/XN/UC and DEH-P9850BT/XN/ES are constructed the same except for the following: Mark Description DEH-P980BT/XN/UC DEH-P9800BT/XN/UC DEH-P9850BT/XN/ES Detach Grille Assy CXC5593 CXC5594 CXC5595 Grille Unit...
  • Page 12: Exterior(2)

    2.3 EXTERIOR(2) 3 7 63 1515 0 36 75 L 13942296513 32 22 u163 (1) : GEM1024 (3) : GEM1069 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 13 CXM1288 Gear Unit XXA7424 Insulator CNN1499 7P FFC Connector (CN561) VKN1299 ZH Connector 2P (CN971) VKN1928 (2) CONTRAST TABLE DEH-P980BT/XN/UC, DEH-P9800BT/XN/UC and DEH-P9850BT/XN/ES are constructed the same except for the following: u163 Mark Description DEH-P980BT/XN/UC DEH-P9800BT/XN/UC DEH-P9850BT/XN/ES Cord Assy CDE8062...
  • Page 14: Cd Mechanism Module

    2.4 CD MECHANISM MODULE 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 15 CND2584 Lever CND2585 CND2586 Bracket CND2587 CND2588 Lever CND2589 Holder CNV7201 Gear CNV7207 Gear CNV7208 Gear CNV7209 Gear CNV7210 Gear CNV7211 Gear CNV7212 Rack CNV7214 CNV7216 Roller CNV7218 Gear CNV7219 u163 Guide CNV7361 Gear CNV7595 Guide CNV7799 CNV7805 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 16: Block Diagram And Schematic Diagram

    3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM 3 7 63 1515 0 TUNER AMP UNIT 10 9 8 18 19 20 21 FM/AM TUNER UNIT : DEH-P980BT/XN/UC : DEH-P9800BT/XN/UC : DEH-P9850BT/XN/ES IC 3 EEPROM IC 5 3.3V 5.0V...
  • Page 17: Http://www.xiaoyu163.com 6 8 7

    KYDT u163 SWVDD ILM+B FLPOPN ILM+B Q831 ILMPW SWVDD VDD REGULATOR FOPNSW SWVDD Q901 FCLSSW Q902 FLPPW Q832 DSENS Q601 DSENS RESET SYSPW2 RESET IC661 X601 reset DSPPW DSPPW S-80835CNUA-B8U 20MHz XOUT SYSPW SYSPW RST1 Q661 DALMON DALMON DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 18 DIS2A OELINT XINT Q1731 BTLED 3.3V FLRESET FLRESET X1761 8.0MHz IC1831 : B,C Xout PD8161A PD8162A D0-15 D0-15 : DEH-P980BT/XN/UC DATA BUS : DEH-P9800BT/XN/UC A0-19 A0-19 : DEH-P9850BT/XN/ES ADDRESS BUS OELGND IC1762 TC7WH34FU ROMBK0 ROMBK0 ROMBK1 ROMBK1 ROMBK2 ROMBK2 P2CECS...
  • Page 19 IC22 CKAB IC21 GCLKBA TC7PAU04FU TC74VHC02FTS1 GPSO BT3V BT3V LATCH DIS2A SIOF_MCLK BT3V HFMCK SCO_CLK_OUT 3.3V 3.3V X21 11.2896MHz EXTAL 5V 26 IC23 TC7PAU04FU BT3V BRCLK PGND PGND X22 12.288MHz OELGND DGND HFAV HFAV SIOF_SS1 FSCHG PTB1 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 20: Overall Connection Diagram(guide Page)

    3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) 3 7 63 1515 0 Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". : DEH-P980BT/XN/UC Large size : DEH-P9800BT/XN/UC SCH diagram : DEH-P9850BT/XN/ES...
  • Page 21 Therefore, when replacing, be sure to use parts of are expressed as : Symbol indicates a capacitor. ← identical designation. No differentiation is made between chip capacitors and ← 0.022 R022 CN1701 discrete capacitors. DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 22 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 23 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 24 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 25 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 26: Tuner Amp Unit(dsp)

    3.3 TUNER AMP UNIT(DSP) 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 27 3 7 63 1515 0 TUNER AMP UNIT(DSP) L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 28: Keyboard Unit

    3.4 KEYBOARD UNIT 3 7 63 1515 0 REMOTE CONTROL SENSOR RESET L 13942296513 MULTI-CONTROL SOURCE DISP LIST CLOCK PHONE BAND/ESC OPEN/EJECT u163 OEL MODULE MXK8230 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 29 3 7 63 1515 0 KEYBOARD UNIT DISPLAY CONTROLLER L 13942296513 : DEH-P980BT/XN/UC : DEH-P9800BT/XN/UC : DEH-P9850BT/XN/ES u163 LE MXK8230 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 30: Cd Core Unit(comp1d)(guide Page)

    3 7 63 1515 0 PICKUP UNIT(P10.5)(SERVICE) L 13942296513 SWITCHES: CD CORE UNIT(COMP1D) S901:HOME SWITCH..ON-OFF S903:DSCSNS SWITCH..ON-OFF S904:12EJ SWITCH.....ON-OFF S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. CD DRIVER M1 CXC6742 SPINDLE MOTOR M2 CXC4026 LOADING/CARRIAGE MOTOR u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 31 SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE CD CORE UNIT(COMP1D) + 3.3 V REGULATOR L 13942296513 CN702 CD3VON(MCKRQ) SRAMLEVEL2 ADENA SRAMLEVEL1 PE5552A SRAMLEVEL0 (S904) CD CONTROLLER (S905) ¤ ⁄ & u163 CN701 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 32 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 33 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 34 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 35 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 36 500 mV/div ! TE 500 mV/div 8 TIN 500 mV/div CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation (Wider) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: u163 Normal Normal Normal DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 37 8 TIN 8 TIN 5 V/div 500 mV/div 500 mV/div CD-DA → CD-ROM mode change(Band key) CD-ROM → CD-DA mode change(Band key) 8 cm CD Eject operation Ref.: Ref.: Ref.: REFO REFO Mode: Mode: Mode: Normal Normal Normal u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 38 & LRCK ! TE 2 V/div 500 mV/div ) LRCKOK ¤ EMPH 2 V/div 5 V/div Tracks Jump(EMPH : OFF → ON) 12 cm CD-DA Source On setup operation Ref.: Ref.: REFO Mode: Mode: Normal Normal L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 39 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 40: Bluetooth Unit, Antenna Unit

    3.6 BLUETOOTH UNIT, ANTENNA UNIT 3 7 63 1515 0 L 13942296513 COMPOUND UNIT u163 ANTENNA UNIT DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 41 3 7 63 1515 0 BLUETOOTH UNIT CN551 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 42: Pcb Connection Diagram

    2.Viewpoint of PCB diagrams WIRED REMOTE CONTROL INPUT Capacitor Connector (DEH-P980BT/XN/UC, DEH-P9800BT/XN/UC) AUX INPUT SIDE A IP-BUS SIDE B Chip Part P.C.Board > FU 321 (A,136,130) Fuse 3 A CEK1286...
  • Page 43 3 7 63 1515 0 SIDE A M972 FAN MOTOR CORD ASSY CORD ASSY ANTENNA CABLE (PRE OUTPUT) (POWER SUPPLY,SPEAKER) L 13942296513 CN902 M801 FLAP MOTOR CN901 16 18 u163 CN1701 FRONT DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 44 3 7 63 1515 0 TUNER AMP UNIT L 13942296513 TESTIN u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 45 3 7 63 1515 0 SIDE B L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 46: Keyboard Unit

    4.2 KEYBOARD UNIT 3 7 63 1515 0 KEYBOARD UNIT PHONE LIST MULTI-CONTROL DISP CLOCK SOURCE BAND/ESC OPEN/EJECT L 13942296513 KEYBOARD UNIT u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 47 3 7 63 1515 0 SIDE A RESET L 13942296513 SIDE B OEL MODULE u163 CN811 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 48: Cd Core Unit(comp1d)

    4.3 CD CORE UNIT(COMP1D) 3 7 63 1515 0 SIDE A CD CORE UNIT(COMP1D) PICKUP UNIT(P10.5)(SERVICE) CN702 CN701 REFO1 L 13942296513 HOME CN901 LOADING /CARRIAGE MOTOR SPINDLE MOTOR IC203 IC301 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 49 3 7 63 1515 0 SIDE B CD CORE UNIT(COMP1D) 12EJ DSCSNS L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 50: Bluetooth Unit

    4.4 BLUETOOTH UNIT 3 7 63 1515 0 SIDE A BLUETOOTH UNIT CN551 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 51 3 7 63 1515 0 SIDE B BLUETOOTH UNIT L 13942296513 u163 ANT1102 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 52: Antenna Unit

    4.5 ANTENNA UNIT 3 7 63 1515 0 SIDE A ANTENNA UNIT L 13942296513 SIDE B ANTENNA UNIT BT ANTENNA u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 53: Switch Unit

    4.6 SWITCH UNIT 3 7 63 1515 0 SWITCH UNIT CN801 CLOSE OPEN L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 54: Electrical Parts List

    Unit Number : CWN1771 Q 37 (A,16,12) Transistor DTC124EUA Unit Name : Bluetooth Unit (A,23,24) Inductor CTF1394 Unit Number : CWN1436 (DEH-P980BT/XN/UC) L 21 (A,26,39) Inductor CTF1379 L 22 (A,23,40) Inductor CTF1379 Unit Name : Tuner Amp Unit L 23...
  • Page 55 C 76 (A,13,45) CKSRYB102K50 R 79 (B,11,32) RS1/16S0R0J R 80 (A,3,33) RS1/16S101J Unit Number : CWN1436 R 81 (B,10,29) RS1/16S101J (DEH-P980BT/XN/UC) R 82 (B,16,29) RS1/16S101J Unit Name : Tuner Amp Unit R 83 (B,9,32) RS1/16S101J R 84 (B,16,31) RS1/16S0R0J MISCELLANEOUS...
  • Page 56 (A,161,91) Diode 1SR154-400 L 404 (B,167,149) Chip Coil LCTAW4R7J2520 D 431 (A,32,125) Diode RSB6R8S L 501 (B,95,22) Inductor CTF1379 D 441 (B,39,118) Diode RSB6R8S L 511 (B,94,35) Inductor CTF1379 D 442 (B,50,121) Diode RSB6R8S L 521 (B,84,23) Inductor CTF1379 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 57 (B,115,97) RS1/16S104J R 304 (A,98,86) RS1/16S682J R 201 (B,54,88) RS1/16S104J R 305 (A,101,82) RS1/16S682J R 202 (B,52,88) RS1/16S104J R 306 (A,101,86) RS1/16S682J R 203 (B,57,79) RS1/16S153J R 307 (B,100,79) RS1/16S102J R 204 (B,63,84) RS1/16S222J R 308 (B,103,83) RS1/16S102J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 58 (B,82,31) RAB4C101J R 757 (B,121,31) RS1/16S104J R 522 (B,88,25) RS1/16S101J R 758 (B,119,35) RS1/16S222J R 523 (B,88,23) RS1/16S101J R 759 (B,120,38) RS1/16S471J R 531 (B,51,42) RS1/16S223J R 760 (B,120,28) RS1/16S471J R 532 (B,49,43) RS1/16S102J R 761 (B,115,39) RS1/16S473J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 59 (A,87,77) CSZS100M16 R 941 (A,82,118) RS1/16S103J C 227 (A,84,83) CKSRYB104K16 R 951 (A,91,119) RS1/16S102J C 228 (A,93,87) CEVW100M10 R 952 (A,89,121) RS1/16S472J C 229 (A,93,81) CEVW100M10 R 953 (A,92,124) RS1/16S472J C 230 (A,93,76) CEVW100M10 R 954 (A,90,124) RS1/16S153J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 60 (A,124,135) CKSQYB225K10 C 751 (A,138,41) CEJQ4R7M35 C 361 (A,126,135) CKSQYB225K10 C 752 (A,138,46) CEJQ1R0M50 C 363 (B,122,140) CKSRYB474K10 C 753 (A,138,35) CEJQ4R7M35 C 364 (B,121,135) CKSRYB474K10 C 754 (B,112,38) CKSRYB104K16 C 365 (B,122,138) CKSRYB474K10 C 755 (B,119,31) CKSRYB102K50 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 61 (B,72,132) CKSQYB105K16 C 966 (B,73,145) CKSQYB105K16 Q 661 (B,155,56) Transistor 2SC4081 C 967 (A,74,135) CKSQYB105K16 Q 721 (A,18,74) Transistor 2SD2396 Q 722 (A,36,72) Transistor UMD3N C 968 (A,72,135) CKSQYB105K16 Q 791 (B,57,107) Transistor 2SD1760F5 C 969 (A,69,135) CKSQYB105K16 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 62 FM/AM Tuner Unit CWE1951 D 811 (B,115,13) Diode DAN202U RESISTORS D 812 (B,124,13) Diode DAP202U D 813 (A,111,27) Diode DAN202U R 101 (B,26,130) RS1/16S181J D 814 (A,107,27) Diode DAP202U R 102 (B,36,124) RS1/16S181J D 815 (B,106,15) Diode DAN202U DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 63 (A,102,66) RS1/16S681J R 394 (A,37,65) RS1/16S473J R 270 (A,100,66) RS1/16S681J R 405 (B,167,114) RS1/16S681J R 271 (A,77,72) RS1/16S0R0J R 406 (B,173,130) RS1/16S681J R 273 (A,82,67) RS1/16S0R0J R 407 (B,173,132) RS1/16S681J R 274 (A,87,72) RS1/16S0R0J R 408 (B,173,134) RS1/16S681J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 64 (A,131,52) RS1/16S104J R 811 (B,110,26) RS1/16S222J R 633 (B,136,57) RS1/16S104J R 812 (B,112,18) RS1/16S222J R 636 (A,120,57) RS1/16S0R0J R 813 (B,110,28) RS1/16S222J R 640 (A,120,55) RS1/16S0R0J R 814 (B,115,17) RS1/16S222J R 652 (A,149,76) RS1/16S104J R 815 (A,116,27) RS1/16S222J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 65 (A,130,113) CKSRYB105K10 C 294 (A,101,74) CCSRCH331J50 C 136 (A,122,117) CEJQ470M10 C 295 (B,96,68) CKSRYB105K10 C 137 (A,129,117) CEJQ470M10 C 296 (B,104,74) CKSRYB105K10 C 138 (A,107,90) CKSRYB104K16 C 297 (B,89,76) CKSRYB104K16 C 139 (B,119,111) CKSRYB105K10 C 301 (A,98,80) CCSRCH681J50 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 66 (B,94,37) CKSRYB104K16 C 844 (A,36,29) CEJQ330M16 C 521 (B,84,18) CKSRYB104K16 C 851 (B,65,15) CKSRYB473K25 C 554 (A,46,63) CEJQ330M10 C 852 (A,92,14) CKSRYB104K16 C 561 (A,51,66) CEJQ220M16 C 861 (A,61,97) CKSRYB105K6R3 C 562 (B,63,43) CKSRYB103K50 C 862 (A,61,99) CKSRYB103K50 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 67 (A,95,39) IC TC74VHC08FTS1 D 132 (B,124,112) Diode 1SS355 IC 521 (A,99,20) IC S99-50084 D 133 (B,124,108) Diode RB521S-30 IC 561 (B,65,38) IC NJM2885DL1-33 D 134 (B,124,110) Diode RB521S-30 IC 566 (B,50,39) IC NJM2872F05 D 181 (A,107,127) Diode HZU3R9(B1) DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 68 (A,63,68) Inductor CTF1389 R 181 (A,102,130) RS1/16S104J L 221 (A,84,85) Inductor CTF1379 R 182 (B,110,125) RS1/16S683J L 241 (B,84,52) Inductor CTF1389 R 183 (A,98,130) RS1/16S153J L 261 (A,56,70) Inductor CTF1379 R 184 (B,116,125) RS1/16S682J L 262 (A,95,66) Inductor CTF1379 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 69 (A,98,71) RS1/16S682J R 451 (A,45,116) RS1/16S104J R 294 (A,98,76) RS1/16S682J R 452 (A,47,117) RS1/16S104J R 295 (A,101,71) RS1/16S682J R 501 (B,95,24) RS1/16S681J R 296 (A,101,76) RS1/16S682J R 502 (B,95,26) RS1/16S681J R 297 (B,100,68) RS1/16S102J R 503 (B,89,31) RAB4C681J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 70 (A,116,69) RS1/16S104J R 911 (A,22,116) RS1/16S821J R 721 (B,24,65) RS1/4SA391J R 921 (B,16,85) RS1/16S821J R 751 (B,135,39) RS1/16S393J R 931 (A,69,116) RS1/16S104J R 752 (B,129,51) RS1/16S104J R 932 (A,75,118) RS1/16S103J R 753 (B,135,41) RS1/16S472J R 933 (B,70,121) RS1/16S473J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 71 (B,124,124) CKSQYB474K16 C 216 (B,68,67) CCSRCH680J50 C 353 (B,126,123) CKSQYB474K16 C 217 (B,50,88) CKSYB106K6R3 C 354 (B,122,124) CKSQYB474K16 C 220 (B,65,94) CKSRYB103K50 C 355 (A,117,122) CEJQ330M10 C 221 (B,81,86) CCSRCH101J50 C 357 (A,86,125) 3 300 µF/16 V CCH1486 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 72 C 913 (A,13,120) CEJQ101M10 C 613 (B,134,78) CCSRCH331J50 C 921 (A,31,99) 470 µF/16 V CCH1325 C 662 (B,155,51) CKSRYB104K16 C 922 (B,30,81) CKSRYB103K50 C 663 (A,156,59) CKSRYB105K10 C 923 (A,30,77) CEJQ101M10 C 721 (B,30,74) CKSRYB473K25 C 932 (B,74,121) CKSRYB104K16 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 73 (B,143,23) Inductor CTF1617 R 1772 (B,108,28) RS1/16S101J L 1762 (B,144,16) Inductor CTF1617 L 1861 (B,159,19) Inductor CTF1617 R 1773 (B,107,37) RS1/16S101J L 1862 (A,113,14) Inductor LCTC1R0K2125 R 1775 (B,79,7) RAB4CQ101J L 1863 (A,126,7) Inductor LCTC1R0K2125 R 1776 (B,105,37) RS1/16S101J DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 74 CKSRYB104K16 u163 S 903 (B,23,78) Switch(DSCSNS) CSN1067 C 1741 (A,50,40) CKSRYB104K16 S 904 (B,42,87) Switch(12EJ) CSN1068 C 1744 (A,50,7) CKSRYB104K16 S 905 (B,28,88) Switch(8EJ) CSN1068 C 1746 (A,16,20) CKSRYB104K16 C 1747 (A,11,11) CKSRYB104K16 RESISTORS C 1748 (B,62,26) CKSRYB103K50 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 75 R 909 (B,16,65) RS1/16SS0R0J CAPACITORS C 103 (B,57,83) CEVW101M16 C 108 (A,47,66) CKSSYB104K10 C 201 (B,46,56) CKSSYB102K50 u163 C 202 (B,47,58) CKSSYB104K10 C 205 (A,34,63) CKSSYB104K10 C 208 (B,34,54) CKSSYB104K10 C 209 (B,31,57) CKSSYB104K10 C 210 (A,31,66) CKSRYB105K10 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 76: Adjustment

    Normal display BT antenna test All lights on BT flash memory test All lights off Data and address bus connection check L 13942296513 [EQ] + [CLOCK] key Display of microcomputer version information Display of ROM correction version information u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 77: Cd Adjustment

    • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 78 • When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 79: Checking The Grating After Changing The Pickup Unit

    Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint u163 Reloading the disc changes the clamp position and may decrease the "wobble". DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 80 Ech → Xch 20 mV/div, AC Grating waveform 3 7 63 1515 0 Fch → Ych 20 mV/div, AC 0° 30° 45° 60° L 13942296513 75° 90° u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 81: Error Mode

    Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 82: System Microcomputer Test Program

    2.There is a definite relation between alternating current frequency and the engine revolution number. Frequency at 4 000 rpm can be set by user operation. Linear complement between 0 rpm = 0 Hz and 4 000 rpm. - Block Diagram ACC Line u163 To microcomputer F/V IC DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 83: E.vol Ic Oscillating Frequency Adjustment

    E.VOL IC oscillating frequency adjustment when you change the VR121, R135 or IC121. - E.VOL IC Oscillating Frequency Adjustment Adjustment Point Switch Position Adjustment Method Frequency Counter : 400 kHz ± 10 kHz VR121 Source : except for AM u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 84: Bluetooth Test Mode

    This enables user to avoid the task of registering phones and transfering phone directory again even after resetting system at the time of battery exchange, etc. • Registration of phone • Phone directory • History of sending/arrival • Dial preset L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 85 The following 3 items are to be confirmed for the simple BT action check by using BT-compliant mobile phone: • Confirmation of Bluetooth connection (certification connection and voice connection) • Confirmation of BT antenna sensitivity (connection) • Confirmation of FLASH memory action 3. Configuration Diagram L 13942296513 DEH-P980BT/XN/UC DEH-P9800BT/XN/UC DEH-P9850BT/XN/ES Bluetooth u163 DEH-P980BT/XN/UC...
  • Page 86 Read out the written data, and verify that both of them match. Read out after total delete, and verify that the deletion has been accomplished. Verification is OK if OK is displayed. Test is complete if everything progressed normally up to this point. u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 87 The following confirmation is to be conducted by test mode in order to simply check BT actions using 2.4 GHz-compliant spectrum analyzer. * Confirmation of output level of Bluetooth unit 3. Configuration Diagram 2.4 GHz-compliant spectrum analyzer DEH-P980BT/XN/UC DEH-P9800BT/XN/UC DEH-P9850BT/XN/ES Remove CD mechanics and L 13942296513...
  • Page 88 [When executing Local TX NM] As per above, measure output level of each frequency with spectrum analyzer upon connection. A standard of judgment should be within the following range of output level V. "-6 dBm < V < 4 dBm" u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 89: General Information

    Removing the CD Mechanism Module (Fig.1) Remove the four screws. Disconnect the connector and then remove the CD Mechanism Module. Fig.1 L 13942296513 Removing the Cord Assy (Fig.2) Disconnect the Cord Assy by Jig GGF1539. Cord Assy Fig.2 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 90 Do not insert the cord assy in extreme slant, as the connector might suffer damage. - Removing the Grille Assy (Fig.4) L 13942296513 Remove the four screws. Disconnect the connector and then remove the Grille Assy. Grille Assy Fig.4 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 91 - Removing the Tuner Amp Unit (Fig.5) 3 7 63 1515 0 Remove the three screws. Straighten the tabs at three locations indicated. Remove the screw and then remove the Tuner Amp Unit. Tuner Amp Unit Fig.5 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 92 3. While lifting the Carriage Mechanism, remove it from the three Dampers. Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. L 13942296513 Damper Damper Carriage Mechanism Lower Frame u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 93 Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw. L 13942296513 Poly Washer Change Arm Pickup Lock Arm Inner Holder Feed Screw Planet Gear Pickup Rack Chassis Pickup u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 94: Connector Function Description

    7.1.2 CONNECTOR FUNCTION DESCRIPTION 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 95 Thermal Protection Bandgap Reference L 13942296513 CONTROL PD8161A (DEH-P9800BT/XN/UC, DEH-P9850BT/XN/ES) PD8162A (DEH-P980BT/XN/UC) BYTE# D15/A-1 D15 / A-1 : Data output / Address input A0 to A22 : Address inputs D0 to D14 : Data outputs CE# : Chip enable input...
  • Page 96 Output of 33.868 8 MHz(CLK for SDRAM) C33M DRAM cs (rcs) Output of DRAM address 11 RA11 Output of DRAM CKE (CKE) Output of DRAM ras cas)(LDQM) Output of DRAM lower cas(LDQM) cas!(UDQM) Output of DRAM upper cas(UDQM) u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 97 Connected to the capacitor for output of REFOUT REFC Reversal input of FE Output of FE Input of FE, TE A/D converter ADIN Reversal input of TE Output of TE Output of LD Input of PD Ground for digital circuits D.GND UPD63763CGJ u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 98 VD power supply control output VDCONT CD LSI serial data input CD LSI serial data output CD LSI serial clock output xwait CD LSI wait control signal input CD LSI address strobe output XASTB Address/data Bus 0 Not used u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 99 Address/Data Bus 5 FLMD1 Not used 77-90 Not used 91-93 csens Not used Not used TYPE_A/D Not used 96,97 Not used TEMP VD power supply short sense input VDSENS DSCSNS Not used PE5552A Format meaning C MOS L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 100 Data bus 15-0 input / output 87,88 Not used JOYST Rotary commander data input Not used kd@-kd) 91-93 Key data input AVSS GND connection Not used VREF GND connection AVCC VCC connection 98,99 Not used OELROMCS E2 ROM : Chip select output u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 101 BYTE : 8 bit / 16 bit mode select input 6 2B 2Y 3 Vss : Ground Vcc : Power supply GND 4 5 2A GP1UX51RK - Block Diagram - Pin Layout Limiter B.P.F Demodulator Integrator Comparator vout GND VCC GND VCC vout u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 102 Frame Memory XINT D[15:0] LP1A LP2A 512 byte DIS1A Color Palette DIS2A GCLKRA SEDI GCLKGA SECS OLED Serial GCLKBA SECK SEDO LP1B LP2B DIS1B MPUSEL DIS2B SWAP GCLKRB XRESET GCLKGB TESTEN GCLKBB u163 GPRO[7:0] GPSO General GPCK Purpose DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 103 R out AK7732VT - Pin Layout L 13942296513 EECS I2CSEL EESO EESEL EECK BVSS EESI DVDD BVSS DVSS DVSS DVDD RQ/CAD1 DVSS 64pin LQFP DVDD LRCLK_O BITCLK_O SI/CAD0 SDOUT1 DVSS SDOUT2 DVDD SDOUT3 SCLK/SCL SDOUT4 SDOUT5 CLKO2 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 104 JX1_E JX2_E L 13942296513 CRC_E EESI EESI EESEL EESEL EECK EECK TESTI1 EECS EECS TESTI2 EESO EESO EEPIL INIT_RESET EEST CONTROLLER S_RESET CK_RESET CKM[3:0] PLL&DIVIDER (Master="L",Slave="H") CLKO2 I2CSEL CLKO2E_N SMODE CLKO1 CLKO1E_N BITCLK_O BITCLK_I LFLT LRCLK_O LRCLK_I u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 105 (+15 to -63 dB,-∞ dB) (0 dB/-6 dB) Monaural Source Circuit Volume Circuit Vo1a Vo2a Selector Circuit Vo3a Si4L Vo4a Si3L Vo5a Si2L Vo6a Si1L+ Vo7a Si1L- Vo1b Si1R- Vo2b Si1R+ Vo3b Si2R Vo4b u163 Si3R Vo5b Si4R Vo6b DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 106 Zero Detect Power Supply Manager ZEROA AGND TC74VHCT08AFTS1, TC74VHC08FTS1 1A 1 14 VCC 1B 2 13 4B 1Y 3 12 4A 2A 4 11 4Y 2B 5 10 3B u163 2Y 6 9 3A GND 7 8 3Y DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 107 PAL007B 3 7 63 1515 0 sw_vcc amp_vcc sw_vcc stby 24 25 10 11 12 13 14 15 16 17 18 19 20 21 22 23 L 13942296513 NJM4151M - Pin Layout - Block Diagram u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 108 SERIAL Phrase Control 16 bit PCM D7/DI Table Synthesizer&2 ch Mix D6/SCK 16 bit D5/DO Address Controller interface Loop Volume Digital Filter Commnad Controller 14 bit DAC OPTANA Timing Controller AGND u163 DGND RESET TEST TESTO1 TESTO2 AOUT DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 109 TUNER : PLL clock output AUIWR AUI : Write signal output AUICS AUI : Chip select output AUISDO AUI : Data output AUISCK AUI : Serial clock output AUIRST AUI : Reset output MUTE System mute output u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 110 Bluetooth model select input BTAN _ AUX Source select output(Bluetooth AV profile/AUX) ILMPW Illumination output FLPILM Illumination output inside flap 113-122 Not used TELIN Mobile phone mute input ROT1 Rotary encoder pulse input ROT0 Rotary encoder pulse input u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 111 TUNER : Signal level input VREF A/D converter reference voltage AVCC A/D converter power supply input terminal KYDT GRILLE : Data input PEG260A(DEH-P980BT/XN/UC, DEH-P9800BT/XN/UC) S99-50084 PEG261A(DEH-P9850BT/XN/ES) : Serial clock input : Serial data input HOLD# : Serial data output : Chip select input...
  • Page 112 3 7 63 1515 0 TC74VHC02FTS1 TC7PAU04FU 14 VCC 1 1Y 13 4Y 2 1A 12 4B 3 1B 4 2Y 11 4A 10 3Y 5 2A 9 3B 6 2B 7 GND 8 3A L 13942296513 AN6123MS INPUT OUTPUT u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 113 15 14 13 9 10 11 12 - Block Diagram VFTN L 13942296513 VFTP AMPT BCLK PCM I/F AMPR CODEC Core Internal Main Clock PLLC TAGND MUTEN VREF BGREF RSTN AMP1 AMP2 TEST1 TEST2 TEST3 AMP1O AMP1I AMP2O AMP2I u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 114 Ground of audio block 23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 115: Operational Flow Chart

    In case of the above signal, the communication with Grille microcomputer may fail. Source keys If the time interval is not 300 msec, the oscillator operative may be defective. Source ON SYSPW←H Pin 99 Completes power-on operation. (After that, proceed to each source operation) u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 116: Operations

    8. OPERATIONS 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 117 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 118 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 119 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 120 3 7 63 1515 0 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 121 Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 g p p Portions to be cleaned Cleaning tools Fans Cleaning paper : GED-008 L 13942296513 u163 DEH-P980BT/XN/UC http://www.xiaoyu163.com...
  • Page 122 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2005 K-ZZA.
  • Page 123 http://www.xiaoyu163.com CONTENTS 1. CIRCUIT DESCRIPTIONS ..........................3 3 7 63 1515 0 2. MECHANISM DESCRIPTIONS........................20 3. DISASSEMBLY ............................... 22 L 13942296513 u163 CX-3164 http://www.xiaoyu163.com...
  • Page 124 http://www.xiaoyu163.com 1. CIRCUIT DESCRIPTIONS 3 7 63 1515 0 UPD63763CGJ, multifunctional LSI used in this device, has built-in CD-ROM decoder and MP3/WMA decoder, as shown in Fig.1.0.1, as well as the conventional CD block, allowing to play CD-ROMs, in which MP3/WMA files are recorded, while the recent mainstay of the CD LSI is the LSI integrating the core DSP with DAC or RF amplifier, which are generally used as peripheral circuits.
  • Page 125 http://www.xiaoyu163.com 1.1 PREAMPLIFIER BLOCK (UPD63763CGJ: IC201) 3 7 63 1515 0 In the preamplifier block, the pickup output signals are processed to generate signals that are used in the subsequent blocks: servo, demodulator, and control blocks. Signals from the pickup are I/V converted in the pickup with the preamplifier with built-in photo detectors, and after added with the RF amplifier, they are used to produce such signals as RF, FE, TE, and TE zero-cross signals.
  • Page 126 http://www.xiaoyu163.com 1.1.2 RF and RFAGC amplifiers 3 7 63 1515 0 The output from the photo-detector (A + C) and (B + D) is provided from the RFO terminal as the RF signal (which can be used for eye-pattern check), after it is added, amplified, and equalized inside this LSI. The low frequency component of the voltage RFO is calculated as below.
  • Page 127 http://www.xiaoyu163.com 1.1.3 Focus error amplifier 3 7 63 1515 0 The photo-detector outputs (A + C) and (B + D) are passed through the differential amplifier and the error amplifier, and (A + C - B - D) is provided from the pin 136 as the FE signal. The low frequency component of the voltage FE is calculated as below.
  • Page 128 http://www.xiaoyu163.com 1.1.6 Tracking zero-cross amplifier 3 7 63 1515 0 The tracking zero-cross signal (hereinafter referred to as TEC signal) is obtained by amplifying the TE signal by fourfold, and used to detect the tracking-error zero-cross point. As the purpose of detecting the zero-cross point, the following two points can be named: 1.
  • Page 129 http://www.xiaoyu163.com 1.2 SERVO BLOCK (UPD63763CGJ: IC201) 3 7 63 1515 0 The servo block performs servo control such as error signal equalizing, in-focus, track jump and carriage move. The DSP block is the signal-processing unit, where data decoding, error correction, and compensation are performed. The FE and TE signals, generated in the preamplifier stage, are A/D-converted, and output drive signals for the focus, tracking, and carriage systems via the servo block.
  • Page 130 http://www.xiaoyu163.com 3 7 63 1515 0 Search start Output from FD terminal The broken line in the figure is assumed in the A blind period case without focus servo. FE controlling signals You can ignore this for blind periods. FSS bit of SRVSTS1 resistor RFOK signals The status of focus close is judged from the statuses of FSS and RFOK after about 10 mS.
  • Page 131 http://www.xiaoyu163.com (a) The track jump operation is automatically performed by the auto-sequence function inside the LSI with a command 3 7 63 1515 0 from the microcomputer. For the track jumps used in the search mode, a single track jump and four to 100 multi-track jump are available in this system.
  • Page 132 http://www.xiaoyu163.com 3 7 63 1515 0 (10 TRACK) GAIN UP EQUALIZER 50 mS NORMAL T. BRAKE OPEN SERVO CLOSED 2.9mS (4.10 TRACK JUMP) 5.8mS (32 TRACK JUMP) Fig.1.2.5 Multi-track jump LENS MOVING FORWARDS LENS MOVING BACKWARDS (INNER TRACK TO OUTER) L 13942296513 (TEC "SQUARED UP"...
  • Page 133 http://www.xiaoyu163.com 1.2.3 Carriage servo system 3 7 63 1515 0 The carriage servo system inputs the output of the low frequency component from the tracking equalizer (information on the lens position) to the carriage equalizer, and, after the gain is increased to a certain level, outputs the drive signal from the LSI.
  • Page 134 http://www.xiaoyu163.com 1.2.4 Spindle servo system 3 7 63 1515 0 In the spindle servo system, the following modes are available: 1) Kick Used to accelerate the disc rotation in the setup mode. 2) Offset a. Used in the setup mode after the kick mode, until the TBAL adjustment is completed. b.
  • Page 135 http://www.xiaoyu163.com 1.3 AUTOMATIC ADJUSTMENT FUNCTION 3 7 63 1515 0 In this system, all the circuit adjustments are automated inside the CD LSI. All adjustments are performed whenever a disc is inserted or the CD mode is selected by pressing the source key. Details of each adjustment will be explained below.
  • Page 136 http://www.xiaoyu163.com 1.3.4 Focus and tracking AGC 3 7 63 1515 0 This adjustment is to automatically adjust the focus and tracking servo loop gains. Adjusting procedure 1) Introduce disturbance to the servo loop. 2) The error signals (FE and TE) when disturbance is introduced are extracted through the band pass filter, to obtain the G1 and G2 signals.
  • Page 137 http://www.xiaoyu163.com 1.3.8 Coefficient display of adjustment results 3 7 63 1515 0 For some of the adjustments (FE and RF offset, FZD cancel, F and T gains, and RFAGC), the adjustment results can be displayed and confirmed in the test mode. The coefficient display in each auto adjustment is as follows: 1) FE and RF offset Reference value = 32 (coefficient of 32 indicates that no adjustment is required)
  • Page 138 http://www.xiaoyu163.com 1.4 POWER SUPPLY AND LOADING BLOCK 3 7 63 1515 0 For the power supply for this system, the VD (7.5 ± 0.5 V) and the VDD (5.0 ± 0.25 V), which are supplied from the motherboard, are used. The three power supplies, the VD mentioned above (for the drive system), the V3R3D obtained from the VD via the 3.3 V regulator (for the control system: 3.3 V) and the VDD (for the microcomputer: 5 V), are used in this system.
  • Page 139 http://www.xiaoyu163.com The load/eject operation is controlled with the status changes of the HOME switch (also used for clamp detection) on the 3 7 63 1515 0 mechanism unit and the three switches on the control unit. The ON/OFF statuses of these switches are respectively detected at the input port of the microcomputer.
  • Page 140 http://www.xiaoyu163.com 3 7 63 1515 0 EJECT 12cm 12EJ DSCSNS HOME CLCONT LOEJ MOTOR STOP EJECT STOP 12EJ DSCSNS HOME L 13942296513 CLCONT LOEJ MOTOR STOP EJECT STOP Dead zone Fig.1.4.4 Status change in LOAD and EJECT modes u163 CX-3164 http://www.xiaoyu163.com...
  • Page 141 http://www.xiaoyu163.com 2. MECHANISM DESCRIPTIONS 3 7 63 1515 0 - Loading actions 1. When a disc is inserted, SW Arm L and R rotate and SW1 is switched from ON to OFF. When SW1 is switched from ON to OFF, the Load Carriage Motor is started and the rubber roller rotates. 2.
  • Page 142 http://www.xiaoyu163.com - Clamp actions mechanism 3 7 63 1515 0 1. With an 8 or 12cm-disc centered on the spindle, the Detection Arm is moved. 2. The movement of the Detection Arm engages the Loading Rack with the 2-Stage Gear. 3.
  • Page 143 http://www.xiaoyu163.com 3. DISASSEMBLY 3 7 63 1515 0 - How to hold the Mechanism Unit 1. Hold the Upper and Lower Frames. 2. Do not hold the front portion of the Upper Frame, because it is not very solid. Do not squeeze this area. - Removing the Upper and Lower Frames 1.
  • Page 144 http://www.xiaoyu163.com - Removing the Guide Arm Assy 3 7 63 1515 0 1. Remove the Upper and Lower Frames and set the mechanism to the eject mode. Bevel Gear Bracket 2. Remove the two Screws and Bevel Gear Bracket. (Note that the gears will come off.) 3.
  • Page 145 http://www.xiaoyu163.com - How to remove the CD Core Unit Shorting Solder 1. Apply Shorting Solder to the flexible cable of 3 7 63 1515 0 the Pickup, and disconnect it from the connector. 2. Unsolder the four leads, and loosen the Screw.
  • Page 146 http://www.xiaoyu163.com - How to remove the Pickup Unit 1. Make the system in the carriage mechanism mode, and have it clamped. 3 7 63 1515 0 2. Remove the CD Core Unit and remove the leads from the Inner Holder. 3.
  • Page 147 http://www.xiaoyu163.com - How to remove the Load Carriage Motor Assy Gear Bracket 1. Make the system in the carriage mechanism 3 7 63 1515 0 Screw A Screw B mode, and have it clamped. Bevel Gear Bracket 2. Release the leads (orange and purple) of Load Carriage Motor Assy from the CD Core Unit and remove the holder.
  • Page 148 http://www.xiaoyu163.com - How to remove the Clamp Arm Assy 1. Make the system in the carriage mechanism mode, and set the mechanism to the eject mode. 3 7 63 1515 0 2. Remove the three Springs. 3. While pressing the position A, turn the Clamp Arm Assy upward, slide it to the left, and remove. Caution: When assembling, place the boss of the Detection Pin in the cam unit of the Loading Rack.

Comments to this Manuals

Symbols: 0
Latest comments: