Declaration Of Conformity - Bosch GST Professional 18 V-LIS Original Instructions Manual

Technical Data
Cordless Jigsaw
Article number
Rated voltage
Stroke rate at
no load n min
0
Stroke mm
Cutting capacity, max.
– in wood mm
– in aluminium mm
– in non-alloy steel mm
Bevel cuts (left/ right),
max.
Weight according to
EPTA-Procedure
01/2003
Permitted ambient
temperature
– during charging
2
– during operation
and during storage
Recommended
batteries
Recommended
chargers
1 dependent of the battery pack being used
2 Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined
according to EN 60745-2-11.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector
h
sum) and uncertainty K determined
according to EN 60745:
Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
Bosch Power Tools
GST 18 V-LIS GST 18 V-LIB
3 601 EA5 1.. 3 601 EA6 1..
V= 18
-1
550–2700 0–2700
23
120
20
8
° –
1
kg 2.2/2.4 2.2/2.4
°C 0...+45 0...+45
°C –20...+50 –20...+50
GBA 18V.. GBA 18V..
AL 18.. AL 18..
GAL 3680 GAL 3680
dB(A) 79
dB(A) 90
dB 3
2
m/s 7.5
2
m/s 1.5
2
m/s 8
2
m/s 1.5
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
18
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
23
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
120
period.
20
Identify additional safety measures to protect the operator
8
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
45

Declaration of Conformity

We declare under our sole responsibility that the product de-
1
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
cluding their amendments and complies with the following
standards: EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 11.06.2014
Assembly
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
81
the On/Off switch.
92
3
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
6
battery charger before using your power tool for the first time.
1.5
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
8.5
does not damage the battery.
1.5
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
English | 15
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
2 609 932 922 | (24.6.14)