Table of Contents
Related Manuals for MULTIQUIP J-SERIES
Summary of Contents for MULTIQUIP J-SERIES
- Page 1 OPERATION AND PARTS MANUAL J-SERIES (CHINA) WALK-BEHIND TROWEL Revision #3 (07/07/10) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. P/N 20840...
-
Page 2: Here's How To Get Help
FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 PAGE 2 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 3: Table Of Contents
Spider and Blades ..........24-25 Gear Box and Engine Mounts ......26-27 Engine .............. 28-29 NOTE: Specification and part number are subject to change without notice. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 3... -
Page 4: General Safety Guidelines
Always refuel in a well ventilated area, away from sparks and open flames. Never smoke while refueling. Exhaust fumes are lethal! Operate machine in a well ventilated area, away from places where fumes can accumulate. PAGE 4 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 5: Explanation Of Codes In Remarks Column
Multiquip. Other entries will for sale through Multiquip. be clarified in the “Remarks” Column. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 5... -
Page 6: Safety Information
Do not operate the machine in dangerous surroundings. PAGE 6 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 7: Fuel
Keep machinery in proper running condition. Make sure that there is no buildup of concrete, grease, oil or debris. Keep all parts properly installed. Fix damage immediately and always replace worn or broken parts. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 7... -
Page 8: Instructions
Considerable force may be required to do this! Release the trigger to lock the spring in this compressed position. STEP 4 STEP 4 STEP 4 STEP 4 STEP 4 PAGE 8 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) - Page 9 Note: A red wire piece has been placed on the engine throttle assembly to show where the throttle cable from your handle should be placed. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 9...
- Page 10 On Robin engines, the hook on the engine end of the throttle wire must be removed. Make the cut as shown (Step 3). The rest of the engine will not require this modification to the throttle cable. PAGE 10 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10)
- Page 11 Serious damage to the machine or personal injury could be caused by dropping a finisher. See “Optional Equipment” in this manual for ordering information. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 11...
- Page 12 2. Check to make sure that the fuel control valve is on and fuel is in the tank. 3. Set safety kill switch (if equipped with centrifugal type clutch) to ON position. 4. Set throttle to idle position. PAGE 12 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10)
- Page 13 Look at the machine while it is running, do the guard rings “rock up and down” relative to the ground? These are some indications that the blade pitch needs to be adjusted. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 13...
- Page 14 1. Place the machine on a flat, level surface. Adjust the blade pitch control to make the blades as flat as possible. Note the blade orientation on the trowel arm. PAGE 14 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10)
-
Page 15: Troubleshooting
0.003" (0.08mm) out of round at the spider attachment point. Blade pitch? Check blades for consistent pitch. Adjust per Maintenance section instructions if necessary. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 15... -
Page 16: Operator Training
It covers basic machine controls and use, but it is not to be considered a complete training exercise. Nor is it to be considered a complete guide to concrete finishing. PAGE 16 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 17: Optional Equipment
Available grinding attachments are used for grinding surface imperfections or joints. These attachments allow greater utilization of your trowel. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 17... -
Page 18: Technical Specifications
Sound pressure may vary depending upon the condition of the motion. The values shown here represent the maximum RMS concrete. Hearing protection is always recommended. value from these measurements. PAGE 18 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) - Page 19 NOTE PAGE J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 19...
-
Page 20: Handle
J-SERIES TROWEL — HANDLE HANDLES ASSY. PAGE 20 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) - Page 21 MICRO SWITCH ........... 1 ..ELECT. 1189 SWITCH CONDUIT KIT ........1 ..ELECT. LIFT HANDLE ASM..........1 ..NO LONGER AVAILABLE 1110 TROWEL CINTROL ASM. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 21...
-
Page 22: Quick Pitch Handle
J-SERIES TROWEL — QUICK PITCH HANDLE™ QUICK PITCH HANDLE ASSY. PAGE 22 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 23: Quick Pitch Handle
CONTROL ARM CONNECTOR ......1 ..SEE ITEM 47 LIFT HANDLE ASM..........1 ..NO LONGER AVAILABLE 1749 TOOL ASM.FOR UNLOADING SPRING ....1 ..SALES ITEM 1754 T-HANDLE ASSY. J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 23... -
Page 24: Spider And Blades
J-SERIES TROWEL — SPIDER AND BLADES SPIDER & BLADES ASSY. PAGE 24 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) -
Page 25: Spider And Blades
UNIVERSAL FIT MOUNTING BAR ....... 3,4 ... SALES ITEM 2878 FLOAT DISK ..............1 ... SALES ITEM 2935 FLOAT DISK LATCH PIN ..........4 ... SALES ITEM J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 25... -
Page 26: Gear Box And Engine Mounts
J-SERIES TROWEL — GEARBOX AND ENGINE MOUNTS GEAR BOX & ENGINE MOUNTS ASSY. PAGE 26 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) - Page 27 REAR ENGINE MOUNT ........... 1 ..GAS 10139 GEARBOX OIL REPLACEMENT, AS REQ........22 OZ. BOTTLE 2616 BEARING REPLACEMENT KIT ............ ITEMS 3,5,7,15, & 16 J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 27...
-
Page 28: Engine
J-SERIES TROWEL — ENGINES, 5 HP B&S, 6.0 HP ROBIN, 5.5 HP HONDA ENGINES, 5 H.P. B&S, 6.0 H.P. ROBIN, 5.5 H.P. HONDA ASSY. PAGE 28 — J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) - Page 29 HHCS 5/16- 24 X 1.1/2” 2742 THROTTLE MOUNT ENGINE 6.0 HP. ROBIN 1393 FHSCS 3/8- 24 X 1.1/2” ........... 1..... ROBIN 0939 SPACER (LIFTING BALE OPTION) ENGINE 5.5 HP. HONDA J-SERIES TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/07/10) — PAGE 29...
- Page 30 © COPYRIGHT 2010, MULTIQUIP INC. Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
Need help?
Do you have a question about the J-SERIES and is the answer not in the manual?
Questions and answers