Jacuzzi J-480 Use, Installation And Maintenance Instructions page 43

I
Mute
Press the mute button (2) once to mute the audio output ("Mute"
flashes on the display). To restore audio output, press the mute
button a second time, or rotate the volume knob.
I
Program Selection
Press the source button (4) to cycle through available program
sources as follows: Tuner - CD - Tuner. If a source is unavailable
(e.g. no CD inserted), that source will not appear on the display.
I
Adjusting Bass Level
Press the audio button (20) until the display reads "BAS. " Rotate the
volume knob to the desired setting. A display of "C O" indicates cen-
ter, -2 to -12 indicates bass cut, and +2 to +12 indicates bass boost.
N.B.: the unit returns to volume mode if the volume control is
not rotated for 3 seconds.
I
Adjusting Treble Level
Press the audio button (20) until the display reads "TRE. " Rotate
the volume knob to the desired setting. A display of "C O" indi-
cates center, -2 to -12 indicates treble cut, and +2 to +12 in-
dicates treble boost.
N.B.: the unit returns to volume mode if the volume control is
not rotated for 3 seconds.
I
Adjusting Balance
Press the audio button (20) until the display reads "BAL. " Ro-
tate the volume knob to the desired setting. A display of "C O"
indicates center, L1 to 15 indicates left balance, and R1 to 15
indicates right balance.
N.B.: the unit returns to volume mode if the volume control is
not rotated for 3 seconds.
Stereo Receiver Operation
I
Adjustment of Fader
Press the audio button (20) until the display reads "FAD. " Rotate
the volume knob to the desired setting. A Display of "C O" indi-
cates center, R1 to 15 indicates rear fade, and F1 to 15 indi-
cates front fade.
N.B.: the unit returns to volume mode if the volume control is
not rotated for 3 seconds.
I
Display Clock
Press the set button (9) to toggle the display between the clock
and radio modes.
When the clock mode is selected, the current time is dispa-
lyed if the controls are left untouched.
I
Set Clock
Press the set button (9) for 2 seconds until the first time digit
flashes on the display. Use button (13) or button (14) to set the
hour, noting the AM/PM at the left.
Briefly press the set button a second time to select the minutes display.
Press the set button a third time to complete the procedure. The
unit remains in clock mode and displays the time after 3 seconds.
N.B.: When power to the spa is shut off for any reason, the
clock will be reset to 12:00.
I
Open/close front panel
Place your thumb on the front panel release button (7) with y-
our forefinger below the front overhang.
Press firmly on the release button, then flip the panel open by
pulling outward at the top edge.
To close the panel, flip the panel up and press firmly until you
hear an audible click.
Keep the front panel closed at all times to prevent water intrusion.
CAUTION: never insert wet discs into the unit or the CD play-
er will be damaged!
I
Radio operation
Press the source button (4) to select the radio mode. The sta-
tion frequency is indicated on the display.
To Select Band: press the band button (12) to toggle through the
radio modes as follows: FM1 - FM2 - FM3 - AM1 - AM2 - FM1.
Each radio band stores up to 6 independent presets, for a total
of 18 FM and 12 AM presets.
To program presets: tune in to the desired radio station, then
press and hold the desired preset button for at least 2 seconds.
"PX", where X = the preset number, appears at the bottom right
of the display.
N.B.: When power to the spa is shut off for any reason, all s-
tation presets are reset to factory settings.
I
Automatically Setting Station Presets
To automatically set station presets to their next higher stations,
press the preset button (1 to 6) from which to start programming,
then press and hold the auto button (16) for at least 3 seconds.The
current station preset and the additional preset memories up to
P6 will be reprogrammed with their next higher stations.
When the auto preset cycle is complete, the unit will remain in
preset scan mode and continue scanning for presets until the
auto button (16) is pressed.
To select only the strongest stations, press the local button (10).
All 18 FM and 12 AM presets can be set sequentially by se-
lecting the next band and continuing the operation during auto
programming.
I
Manual tuning
Press the tune/seek up button (13) once to automatically tune
to the next higher station.
Press the tune/seek up button (14) once to automatically tune
to the next higher station.
To manually tune to a specific station frequency, press and hold
either 13/14 button for at least 2 seconds. Holding the two
buttons will manually increase or decrease the desired frequency.
When you reach the desired frequency, relase the key.
The unit remains in manual tune mode for 3 seconds after ei-
ther button is released so you can fine tune the station fre-
quency with additional button presses.
43