Download Print this page

Yamaha VXC3F-VAW Owner's Manual

Advertisement

Quick Links

SPEAKER SYSTEM
Owner's Manual
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of
serious injury or even death from electrical shock, short-circuiting,
damages, fire or other hazards. These precautions include, but are not
limited to, the following:
Do not open
• This device contains no user-serviceable parts. Do not attempt to
disassemble the internal parts or modify them in any way. If it should appear
to be malfunctioning, discontinue use immediately and have it inspected by
qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp or wet
conditions. If any liquid such as water seeps into the device, turn off the
power of the amplifier immediately. Then have the device inspected by
qualified Yamaha service personnel.
Hearing loss
• When turning on the AC power in your audio system, always turn on the
power amplifier LAST, to avoid hearing loss and speaker damage. When
turning the power off, the power amplifier should be turned off FIRST for the
same reason.
Fire warning
• Do not place any burning items or open flames near the device, since they
may cause a fire.
If you notice any abnormality
• If any of the following problems occur, immediately turn off the power of the
amplifier.
- Unusual smells or smoke are emitted.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
- Cracks or other visible damage appear on the device.
Then have the device inspected or repaired by qualified Yamaha service
personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of
physical injury to you or others, or damage to the device or other property.
These precautions include, but are not limited to, the following:
Location
• Do not place the device in an unstable position where it might accidentally
fall over and cause injuries.
• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.
• Avoid being near the device during a disaster, such as an earthquake. Since
the device may fall and cause injury, stay away from the device quickly and
move to a safe place.
• Before moving the device, remove all connected cables.
• Always consult qualified Yamaha service personnel if the device installation
requires construction work, and make sure to observe the following
precautions.
- Choose mounting hardware and an installation location that can support
the weight of the device.
- Avoid locations that are exposed to constant vibration.
- Use the required tools to install the device.
- Inspect the device periodically.
Connections
• Before connecting the device to other devices, turn off the power for all
devices. Also, before turning the power of all devices on or off, make sure
that all volume levels are set to the minimum. Failing to do so may result in
electric shock, hearing loss, or equipment damage.
• Use only speaker cables for connecting speakers to the speaker jacks. Use
of other types of cables may result in fire.
Installing the Speakers
Install the speakers onto the ceiling with the supplied hardware. Ensure
that the strength of the ceiling rail is sufficiently strong.
Illustrations in this manual are for the VXC3F-VA. The installation method
is the same for other models.
CAUTION
When attaching the speakers, turn off the power amplifier.
Pre-installation (Preparation of the Cable)
• If stranded wires are used for cables, use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has an external diameter
of 2.0 mm or less, and a length of approximately 7 mm.
2.0 mm
approx.
or less
7 mm
• Make sure that the release lever of the baffle front is in the position as
shown in the figure below.
Release lever
1
Cut Out a Hole in the Ceiling
1 Put the supplied cutout template to the ceiling and draw a circle by
tracing it.
Make sure to use the cutout template so that hole is the correct
diameter.
Note
If you use a circular cutter, set the diameter with the cutout template.
2 Cut the hole by tracing the circle.
Be careful to prevent chips or powder entering your eyes while
cutting the hole.
2
Install the Tile Rails and O-ring
1 Insert the two tile rails through the cut hole and place them on the
ceiling surface within your reach. Be sure that each tile rails are
oriented as shown below.
2 Insert the folded O-ring through the cut hole and open it in the
ceiling.
3 Secure the O-ring and tile rails with supplied two screws through
either slot of both O-ring brackets.
O-ring
Tile Rail
20160122
ZT92700
English
Handling caution
• Avoid use excessive force on the connectors to prevent injuries.
• Do not operate the device if the sound is distorting. Prolonged use in this
condition could cause overheating and result in fire.
• Avoid pulling the connected cables to prevent injuries.
• When choosing a power amplifier for use with this device, make sure that the
output power of the amplifier is lower than the power capacity of this device.
If the output power is higher than the power capacity, malfunction or fire may
occur.
• Do not input excessively loud signals that may result in clipping in the
amplifier or cause the following:
- Feedback, when using a microphone
- Continuous and extremely loud sound from a musical instrument, etc.
- Continuous and excessively loud distorted sound
- Noise caused by plugging/unplugging the cable while the amplifier is
turned on
Even if the output power of the amplifier is lower than the power capacity of
this device (program), damage to the device, malfunction or fire may occur.
NOTICE
To avoid the possibility of malfunction/damage to the product, damage to data,
or damage to other property, follow the notices below.
Handling and maintenance
• When using a high-impedance speaker connection, make sure the audio
signal is passed through an 80 Hz or above high-pass filter before being
input to the speakers.
• Do not expose the device to excessive dust or vibration, or extreme cold or
heat (such as in direct sunlight, or near a heater), in order to prevent the
possibility of panel disfiguration, unstable operation, or damage to the
internal components.
• Do not place vinyl, plastic or rubber objects on the device, since this might
discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic changes in
ambient temperature—when the device is moved from one location to
another, or air conditioning is turned on or off, for example. Using the device
while condensation is present can cause damage. If there is reason to
believe that condensation might have occurred, leave the device for several
hours without turning on the power until the condensation has completely
dried out.
• Be sure to observe the amplifier's rated load impedance, particularly when
connecting speakers in parallel. Connecting an impedance load outside the
amplifier's rated range can damage the amplifier.
• Protection Circuit
This speaker system has an internal protection circuit that shuts off the
speaker unit when an excessive input signal is applied. If the speaker unit
emits no sound, reduce the volume level of the amplifier immediately. The
sound will return automatically in several seconds.
• Air blowing out of the bass reflex ports is normal, and often occurs when the
speaker is handling program material with heavy bass content.
• Do not place the speaker face down with the grille attached, as deformation
of the grille may result.
• When placing the speaker face down, always place it on a flat surface.
• Do not touch the speaker driver unit.
• Do not swing the speaker by its carrying band.
About this manual
• The illustrations as shown in this manual are for instructional purposes only.
• The company names and product names in this manual are the trademarks
or registered trademarks of their respective companies.
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the device.
3
Connect the Wiring to the Connector
1 Pull the wiring from the amplifier through the cut hole of the ceiling.
2 Pass the cables through the cable gland attached to the terminal
cover.
If it is difficult to pass all the cables through a single cable gland, open
the hole in the terminal cover and attach a commercially available
cable gland.
Note
Prepare a cable gland of AVC part no. PGB 13.5-12B.
CAUTION
Use an appropriate tool for opening the hole. Otherwise, you may be
injured if you open the hole with your bare hands.
For safety, use the screw hole on the speaker (M5 × 12 mm) and
connect the wire to an independent support point such as a joist.
Example of the connection using an eye bolt
Eye bolt
Safety wire
Screw hole
(M5 × 12 mm)
CAUTION
Always take measures to prevent the speaker from falling down.
Use a safety wire of appropriate length. Should the speaker fall and the
wire is too long, the wire may snap due to excess strain.
3 Loosen the terminal screws of the ceramic terminal with a flat-blade
screwdriver, insert the cables into each terminal and tighten the
screws. Pull on the cables to make sure they are tightly secured and
will not come loose.
+
Earth*
* Use the Earth terminal as necessary.
Note
Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
Less than 3 mm (0.1 in.)
EN
Unpacking
Unpack the contents and confirm that all the following items are included.
• Speaker × 2
• Grille × 2
• Terminal Cover × 2
* The speaker cable and safety wire are not included.
General Specifications
Type
Component
1
Coverage angle (–6 dB) *
175° conical (500 Hz), 175° conical (1 kHz),
160° conical (2 kHz), 95° conical (4 kHz)
Rated impedance
100 V line: 330 Ω (30 W), 670 Ω (15 W), 1.3 kΩ (7.5 W)
70 V line: 170 Ω (30 W), 330 Ω (15 W),
Power rating
NOISE
PGM
MAX
1
Sensitivity *
87 dB (1 W, 1 m, 100 Hz to 10 kHz pink noise)
75 dB (1 W, 4 m, 100 Hz to 10 kHz pink noise)
2
Maximum SPL *
100 dB (30 W, 1 m, 100 Hz to 10 kHz pink noise at 30 W tap)
88 dB (30 W, 4 m, 100 Hz to 10 kHz pink noise at 30 W tap)
109 dB (160 W, 1 m, 100 Hz to 10 kHz pink noise at 8 Ω)
97 dB (160 W, 4 m, 100 Hz to 10 kHz pink noise at 8 Ω)
1
Frequency range (-10 dB) *
Connector
Transformer taps 70 V
100 V
Overload protection
Magnetically shielded
Dust and water resistant
Enclosure
Shape
Cabinet material
Baffle material
Grille
Material
Finish
Dimensions (Including grille)
Ø324 × 143D mm (Ø12-13/16" × D 5-11/16")
Net weight (Including grille)
Cutout size
Required ceiling board thickness
Packaging
Standards
The specifications data was measured in an anechoic chamber, according to EN 54-24.
Reference axis: Axis is on the center of grille surface and perpendicular to the grille surface.
Reference plane: Plane is on the grille surface and perpendicular to the reference axis.
Horizontal plane: Plane is containing the reference axis and perpendicular to the reference plane.
*1: Half-space (2π)
*2: Calculated based on power rating and sensitivity, exclusive of power compression.
The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual
may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file.
The dimensions are shown overleaf.
Connecting the Cable
CAUTION
• When connecting with low impedance, take note of the total
impedance.
• When connecting with high impedance, the total input wattages of the
connected speakers should lie within the margin of the rated input of
the power amplifier. For more information, refer to the description
concerning high impedance connection at the following URL.
Yamaha Pro Audio site "Better Sound for Commercial Installations":
http://www.yamahaproaudio.com/global/en/training_support/
better_sound/
4 Tighten the screw and then attach the terminal cover.
5 Tighten the cap of the cable gland.
Cap
4
Fix the Speakers onto the Ceiling
1 Take care not to trap the cable, carrying band, or safety wire while
slowly pushing the speaker up into the ceiling.
Anti-Drop tab
Make sure the release lever is in the position of the figure below. If it
is set to the position of the figure, when all the Anti-Drop tabs cross
over the O-ring, the speaker is held temporarily.
Release lever
2 While slightly lifting up the speaker, turn the screwdriver clockwise
to tighten the attachment screw.
The first turn of the attachment screw opens the clamp. Further
turns move the clamp down the channel to pull the speaker up into
the ceiling.
Note
When the clamp is difficult to open, turning the screwdriver halfway
counterclockwise once will make it easier to open the clamp.
Clamp
1
• O-ring × 2
• Cutout Template × 1
• Tile Rail × 4
• Owner's Manual (this manual)
• Screw × 4
VXC5F-VA/VXC5F-VAW
VXC3F-VA/VXC3F-VAW
Full range, Bass reflex
4.5" (11.5 cm) Full range unit
3.5" (9 cm) Full range unit
180° conical (500 Hz), 180° conical (1 kHz),
170° conical (2 kHz), 165° conical (4 kHz)
8 Ω (without transformer)
8 Ω (without transformer)
100 V line: 670 Ω (15 W), 1.3 kΩ (7.5 W), 2.6 kΩ (3.8 W)
70 V line: 330 Ω (15 W), 670 Ω (7.5 W),
670 Ω (7.5 W), 1.3 kΩ (3.8 W)
1.3 kΩ (3.8 W), 2.6 kΩ (1.9 W)
40 W
80 W
160 W
86 dB (1 W, 1 m, 100 Hz to 10 kHz pink noise)
74 dB (1 W, 4 m, 100 Hz to 10 kHz pink noise)
96 dB (15 W, 1 m, 100 Hz to 10 kHz pink noise at 15 W tap)
84 dB (15 W, 4 m, 100 Hz to 10 kHz pink noise at 15 W tap)
105 dB (80 W, 1 m, 100 Hz to 10 kHz pink noise at 8 Ω)
93 dB (80 W, 4 m, 100 Hz to 10 kHz pink noise at 8 Ω)
60 Hz – 20 kHz
Ceramic terminal block (3 pin) × 1 (input: +/-, Earth)
2
Applicable wire size AWG 26-12 or 4.0 mm
, wire outer diameter Ø6.5 - Ø12.5 mm
30 W, 15 W, 7.5 W, 3.8 W
15 W, 7.5 W, 3.8 W, 1.9 W
30 W, 15 W, 7.5 W
Full-range power limiting to protect network and transducers
No
IP32 (EN54-24 Enclosure protection rating. Type A: IP21C)
Round
ABS (UL94-5VB), 3.5 mm, black
ABS (UL94-5VB), 5 mm, black
Powder coated perforated steel (t=0.6 mm), trim ring: ABS V-0, aperture ratio: 46%
VXC5F-VA/VXC3F-VA : Black painting (approximate value: Munsell N3)
VXC5F-VAW/VXC3F-VAW : White painting (approximate value: Munsell 9.3)
Ø285 × 112D mm (Ø11-1/4" × D 4-7/16")
3.2 kg (7.1 lbs)
Ø285 mm (Ø11-1/4")
5 mm – 37 mm
Packaged in pair
Certified to the European Standard EN 54-24: 2008 Certified year: 16
- VXC5F-VA/VXC5F-VAW: 0560-CPR-152190027
- VXC3F-VA/VXC3F-VAW: 0560-CPR-152190028
Loudspeaker for voice alarm systems for fire detection and fire alarm systems
Environment type: A
Certified to the European Standard EN60849:1998
Sound systems for emergency purposes
Certified to the International Standard ISO 7240-24: 2010
Sound-system loudspeaker for fire detection and fire alarm systems
In compliance with the British Standard BS-5839-8: 2008 14.8
When installing the multiple speakers, connect them in parallel way.
From amplifier or
previous speakers
Power
Speaker
amplifier
*You can use this terminal to hook up an earth cable, as necessary.
CAUTION
• Do not over-tighten the attachment screw. Otherwise, the
attachment screw and clamp will break.
• Do not turn any screws other than attachment screw. Otherwise,
the speaker may fall or malfunction.
Removing from the Ceiling
1 Loosen the fixing screw by turning the screw counterclockwise.
Loosen the screw and the clamp goes up, and as it reaches the
top, the clamp closes as shown in figure below.
Clamp
2 While slightly lifting up the speaker, secure it by moving the release lever
of the baffle front to the direction of the arrow as shown in the figure.
3 Remove the safety wire from the speaker that is detached from the
ceiling.
5
Set the Line Voltage/Impedance and Power
Select the line voltage/impedance (100 V/70 V/8Ω) and power tap for
100 V/70 V line distributed system, by rotating the tap selector switch on
the front side of the speaker with a flat-blade screwdriver.
Illustration indicates the setting at 15 W for 100 V
line and 7.5 W for 70 V line.
CAUTION
Carrying band
• The "X" position should not be selected. The 8Ω position should be
selected for 8Ω audio systems only. If the setting is incorrect, it may
cause malfunction of the speaker and amplifier.
• Make sure the amplifier is switched off before operating the tap selector
switch.
6
Attach the Grille
Attach the string to the speaker as shown in the figure, then fit the grille to
Anti-Drop tab
the magnets (6 places) on the baffle front.
CAUTION
The grille may fall down if it is attached inadequately. Attach it firmly.
Incorrectly attached
Fixing screw
Yamaha Pro Audio global website
http://www.yamahaproaudio.com/
Yamaha Downloads
http://download.yamaha.com/
20 W
40 W
80 W
71 Hz – 20 kHz
15 W, 7.5 W, 3.8 W
2.6 kg (5.7 lbs)
Ø247 mm (Ø9-3/4")
To subsequent
speakers
To
subsequent
speakers
Magnet
Correctly attached
Manual Development Department
© 2016 Yamaha Corporation
Published 03/2016 CRZC-A0
Printed in Indonesia

Advertisement

loading

Summary of Contents for Yamaha VXC3F-VAW

  • Page 1 Doing so may result in malfunction. The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual • When placing the speaker face down, always place it on a flat surface.
  • Page 2 Unit: mm Old Equipment de Equipamiento Viejo VXC5F-VA/VXC5F-VAW VXC3F-VA/VXC3F-VAW This symbol on the products, packaging, and/or accompanying Este símbolo en los productos, embalaje, y/o documentación que se documents means that used electrical and electronic products should acompañe significa que los productos electrónicos y eléctricos usados not be mixed with general household waste.

This manual is also suitable for:

Vxc3f-vaVxc5f-vawVxc5f-va