Sony RM-IP10 Operating Instructions Manual page 11

EXPAND (expansion method)
• When treating the TALLY/CONTACT connector
as input:
Treats the terminal 1 to 7 as a binary number.
Accepts as number 1 when the terminal 1 is
earthed and terminals 2 to 7 is open.
• When treating the TALLY/CONTACT connector
as output:
Treats the terminal 1 to 7 as a binary number, and
transmits to the external device.
Number 1 is output when the terminal 1 is earthed
and terminal 2 to 7 is high.
About the camera number that is input/
output from the TALLY /CONTACT
connector
Relation between total of 112 cameras (assigned to
the camera numbers 1 to 7 in each of the camera
group numbers 1 to 16) and the camera number of
TALLY/CONTACT connector is as follows.
Camera group Camera Camera number of the
number number TALLY/CONTACT connector
1 1
2
7
2 1
7
1
16
7
Switch 7, 8: LOCK button function selector
The lock has the following two functions.
1 Controls and focus lock: The VALUE/R,
BRIGHT/B, and FOCUS controls and AUTO/
MANUAL button cannot be operated.
2 Joystick lock: The joystick (slanting, dial on the
upper part (zoom), button on the top), MENU
button, and PAN-TILT RESET button cannot be
operated.
You can select the functions that are locked by
using the following settings.
Switch Switch Setting
7 8
OFF OFF Setting 1: Each time you press
the LOCK button, the lock
function changes as follows:
"1" y unlocked
ON OFF Setting 2: Each time you press
the LOCK button, the lock
function changes as follows:
"2" y unlocked
OFF ON Setting 3: Each time you press
the LOCK button, the lock
function changes as follows:
"1 and 2" y unlocked
1
2
7
8
14
106
112
Switch Switch Setting
7 8
ON ON Setting 4: Each time you press
the LOCK button, the lock
function changes as follows:
"1" t "2" t "1 and 2"
t unlocked t "1" t ...
es DIP 2 switch
Switch 1: PANEL LIGHT switch
Turns the PANEL button lighting on or off.
Set ON (the GROUP/POSITION and CAMERA
buttons light in green), or OFF.
This switch setting is valid even if you change the
setting while the power is turned on.
Switch 2: L/R DIRECTION selector
You can reverse the joystick direction.
Set to ON for the reverse operation, or OFF for the
standard operation.
For the standard operation, the camera is preset to
face toward the right (left) when the joystick is
inclined to the right (left). For the reverse operation,
the camera is preset to face toward the right (left)
when the joystick is inclined to the left (right).
This switch setting is valid even if you change the
setting while the power is turned on.
Switch 3: BRIGHT control function selector
Selects the function of the BRIGHT control.
Set to ON for IRIS and GAIN adjustments, or OFF
for IRIS adjustment only.
Switch 4: ALL POSITION setting switch
The ALL POSITION function allows you to set the
all cameras in the camera groups 15 and 16 to the
same preset setting when you load the preset setting
to just one camera in group 15 or 16. (Since preset
setting is performed for 14 cameras sequentially,
they cannot be started simultaneously.)
Set to ON to activate this function, OFF to turn this
function off.
This function works only for the LAN connection.
Switch 5 to 7: Expansion switch
Set to OFF.
Complement:
Setting switch 5 to ON prevents the TALLY lamp of
the camera from lighting in NORMAL TALLY, ON
AIR TALLY or CONTACT (TALLY) mode.
Switch 8: Setting update mode switch
Set to ON to active the setting update mode. When
set to ON, you can set and change the camera table
from the setting software "RM-IP10 Setup Tool,"
and check the firmware version of the unit.
Location and Function of Parts
11
GB