CD Stereo System SC-AK27 SC-AK17 Operating Instructions The illustrations show SC-AK27. Note: The "EB" indication shown on the outside packing case indicates United Kingdom. Before connecting, operating or adjusting this pro- duct, please read these instructions completely. Please save this manual.
AC power supply cord ........ 1 pc. These operating instructions, however, fundamentally explain the operation of system SC-AK27. For United Kingdom For Australia and New (RJA0044-1C) Zealand System SC-AK27 SC-AK17 (RJA0035-X) Main unit SA-AK27 SA-AK17 Speakers SB-AK27 SB-AK17 For others (RJA0019-2K) Remote control transmitter ......
Table of contents Suggestions for safety Placement Before using Avoid placing the unit in areas of : Supplied accessories ..............2 • direct sunlight Suggestions for safety ..............3 • high temperature Caution for AC Mains Lead ............4 • high humidity Concerning the remote control ............
Caution for AC Mains Lead WARNING: DO NOT CONNECT EITHER WIRE TO (For United Kingdom) THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL (“EB” area code model only) COLOURED GREEN OR GREEN/YELLOW. For your safety, please read the following text carefully. THIS PLUG IS NOT WATERPROOF—KEEP DRY.
• Do not attempt to recharge alkaline or manganese batteries. R6, AA, UM-3 • Do not use rechargeable type batteries. SC-AK17 Correct method of use R6, AA, UM-3 Operation notes • Do not place obstacles between the remote control signal sensor and remote control unit.
E X T as shown in the drawing. However there is no problem using the unit. SC-AK27 Red (+) Gray (+) Black (–) Blue (–) SC-AK17 Red (+) Black (–) Connector Appliance inlet approx. 6 mm RQT4708...
Connections For Australia and New Zealand Optional antenna connections FM outdoor antenna (not included) You may need an outdoor antenna if you use this system in a mountainous region or inside a reinforced-concrete building, etc. 75Ω coaxial cable (not included) FM outdoor antenna A 30 mm Disconnect the FM indoor antenna if an FM outdoor antenna is in-...
Functions change according to the source. + Tape edit button (TAPE EDIT) ........25 , Recording start/stop button (a REC/STOP) .... 22 Except for SC-AK17 model and SC-AK27 Australia and New Zealand model DOLBY noise reduction button (DOLBY NR) ...............19 .
Turning the demo function off If the clock has not been set, a demonstration of the display is shown when the unit is switched to standby. This function is set to on at the time of purchase. Turn this function off to get the most from the economy mode (see below).
Setting the time This is a 24-hour display clock. This example in the figure shows how to set the time for 16:25 (4:25 p.m.). Press [f f f f f / 7 7 7 7 7 ] to switch on the system. Press [CLOCK/TIMER] to select “CLOCK”.
Presetting radio broadcasts • Up to 12 stations can be set in each band with the automatic or manual memory presetting. • If broadcast frequencies are preset in the memory, you can easily tune in any of these frequencies from the system or remote control unit.
Listening to radio broadcasts Press [TUNER BAND] to select band. The system will come on automatically. Every time you press the button: FM ↔ AM Press [TUNE MODE] to select “PRESET” or “MANUAL”. Every time you press the button: MANUAL ↔ PRESET. PRESET: For preset stations MANUAL: For non-preset stations...
Listening to compact discs Loading and checking CDs Always stop the changer before loading or changing CDs. You cannot change CDs while a disc is playing. How to load CDs Press [CD]. The system will come on automatically. Press [c c c c c OPEN/CLOSE 1] – [c c c c c OPEN/CLOSE 5], whichever you want.
Listening to compact discs Sequential play Press [CD]. The system will come on automatically. Insert CD in the tray. (For details, see page 14.) Press [DISC 1] – [DISC 5] to select the disc you want. (If the desired CD is indicated on the display panel, the same operation can be accomplished by pressing [-/J].) Play will start from the first track on the selected disc, and will continue until the last track of the final disc (see below)
Listening to compact discs Direct access play by remote control only Press [CD]. Press [DISC]. (within 10 seconds or so) Press [1] – [5] to select the disc you want. Press the numeric button to select the desired track number. The CD will be played from the selected track to the last track of the final disc (page 15).
Listening to compact discs Program play by remote control only You can program up to 24 tracks. Press [CD]. Ensure CD is stopped. Press [PROGRAM]. Press [DISC]. (within 10 seconds or so) Press [1] – [5] to select the disc you want. Press the numeric button to select the desired track.
Listening to compact discs To listen to special CDs and tracks (CD Manager function) This function makes it easier for you to select special CDs and tracks from amongst those loaded in the player. You can use this function to make recordings as well. There are 3 CD/track selection modes.
Insert the tape with the exposed tape facing down. Close the holder by hand. Except for SC-AK17 model and SC-AK27 Australia and New Zealand model Press [DOLBY NR]. You have to turn Dolby NR ON/OFF according to the type of Front side recording you made.
Page 20
• With silent parts found within tunes About the Dolby noise-reduction system Except for SC-AK17 model and SC-AK27 Australia and New Zealand model The Dolby noise-reduction system is designed to effectively reduce the annoying high-frequency “hissing” noise typical of cassette tapes.
V.BASS(for SC-AK17) effect for the playback sound. To erase a recorded sound B Press [TAPE]. Insert the recorded tape into deck 2. Except for SC-AK17 model and SC-AK27 Australia and New Zealand model Press [DOLBY NR] so that the Dolby NR indicator goes off.
Press [c DECK 2 OPEN] and insert the tape. Close the holder by hand. Tape direction is automatically set to “ 3 3 3 3 3 ”. Except for SC-AK17 model and SC-AK27 Australia and New Zealand model Press [DOLBY NR].
Press [c DECK 2 OPEN], and insert the tape. Close the holder by hand. Tape direction is automatically set to “ 3”. Except for SC-AK17 model and SC-AK27 Australia and New Zealand model Press [DOLBY NR]. You have to turn Dolby NR ON/OFF according to the type of recording you want to make.
Recording from compact discs To record special CDs and tracks Front side (CD Manager function) Reverse side This function makes it easier for you to select special CDs and tracks from amongst those loaded in the player. • The interrupted track is re-recorded in its entirety on the While recording, if a track is cut off in the middle at the end of the front reverse side.
Tape-to-tape recording The recording level and the Dolby effect (except for SC-AK17 models and SC-AK27 Australia and New Zealand model) will be recorded as they are on the tape being played back. Press [TAPE]. Press [c OPEN] on both decks and insert the tapes.
All recordings are performed at the flat setting even if an alternative sound quality/sound field setting has been selected and the super woofer effect is set to ON. SC-AK17 Adding bass SC-AK17 only Press [V.BASS]. Press the button again to cancel. SC-AK27 “V.BASS” goes out.
Varying the sound quality with the acoustic image (Al) equalizer The Al equalizer uses the SOFT, SHARP, HEAVY and LIGHT sound quality coordinates to achieve subtle sound quality settings with ease. Dial [SOUND EQ] to display “Al EQ”. When it is turned clockwise, the settings are selected in the following sequence.
Varying the sound quality with the manual equalizer Dial [SOUND EQ] to display “MANUAL”. When it is turned clockwise, the settings are selected in the following sequence. 1 HEAVY 2 CLEAR 3 SOFT 4 DISCO 5 LIVE 6 HALL 7 MANUAL 8 AI EQ 9 FLAT The SOUND EQ lamp lights more brightly, and “FLAT”...
Using the timer Using the play timer Select this timer when you want to use the timer as an alarm clock. You can wake up listening to music (CD, tuner, tape or aux) at a desired volume level and time. Preparations •...
Prepare for recording. 1 Insert a tape into deck 2 with the side on which the recording will start facing you. Except for SC-AK17 model and SC-AK27 Australia and New Zealand model Select [DOLBY NR]. 3 Select the reverse mode.
Using the timer For Australia and Using the play/record timer New Zealand To switch the timer OFF Press [rPLAY/rREC] and check [rPLAY/rREC] indicator lights off. For others If you set the timer incorrectly Repeat the procedure from step 1. To check settings Press [CLOCK/TIMER] to select “rPLAY”...
Using the timer Using the sleep timer To cancel the sleep timer: Press [SLEEP] to select “OFF”. To confirm the remaining time: (only while system is ON) Press [SLEEP]. To change the time remaining during operation: Press [SLEEP] to show the remaining time then press [SLEEP] to select the desired time.
Concerning compact discs With this player, you can only play compact discs having this mark. However, do not use irregular shape CDs. CDs of the sort can damage the unit. XXXX XXXX XXXXX XXXX XX XXXX XXXX XXXXX XXXX XXXX XXXXX XXXX XXXX Handling precautions Handle CDs as shown on the left (...
Troubleshooting guide Before requesting service for this unit, check the chart below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to the directory of Authorized Service Centers (enclosed with this unit) to locate a convenient service center, or consult your dealer for instructions.
Dolby-NR is set in correctly. Match Dolby-NR ON/OFF according to the or unsteady. Except for SC-AK17 model and SC-AK27 type of recording you made. Australia and New Zealand model The deck does not enter the The erase-prevention tabs are removed Attach tape to cover the space left by recording mode.
Technical specifications AMPLIFIER SECTION SC-AK27 SC-AK17 50 dB (A weighted) GENERAL SC-AK27 RMS power output Power supply SC-AK27 THD 10%, both channels driven For United Kingdom, Australia and For Australia and New Zealand 100 W per channel (6 Ω) New Zealand...