Related Manuals for joke DIPROFIL FPT/ER
Summary of Contents for joke DIPROFIL FPT/ER
- Page 1 Instruction manual Hand-filing machine DIPROFIL FPT/ER ® and FPV/ER Order no.: 0 005 204 and 0 005 208...
- Page 2 Please feel free to call our customer service department at any time should you encounter tech- nical problems which are not dealt with in this manual: Telephone 0 22 04 / 8 39 - 0 Telefax 0 22 04 / 8 39 - 60 www.joke.de...
- Page 3 The device is designed exclusively for grinding, milling and polishing with the fools listed and approved in the joke catalogue for surface finishing. Any other use will be deemed to be contrary to its intended purpose. The manufacturer cannot be held liable for any resulting damages.
- Page 4 Surface Technology Warranty/Identification joke warrant the correct manufacture of every joke Technology GmbH product which is delivered in accordance with the terms of contract and delivery. This warranty does not cover damages caused by normal wear and tear, incorrect handling, negligent use, the fitting of non-original spare parts, ina-dequate care and/or a failure to comply with this technical manual.
- Page 5 The connection must be achieved without major resistance. Otherwise, the appropriate position is obtained by slightly rotating the eccentric cam (5.1/5). Only use authorised tools according to the joke catalogue! Figure 5.1 Symbol drawing hand-filling machine „P“...
- Page 6 Oberflächentechnik Surface Technology Pull off the protective hood (5.1/4) to adjust the working stroke. Loosen the clamping screw (5.1/1) and subsequently rotate the loose eccentric cam shaft (5.1/5) such that the index mark on the outer ring points to the figure that indicates the desired stroke in mm.
- Page 7 Oberflächentechnik Surface Technology Notes on operation Notes on operation 0.5 - 3 mm for filing recommended stroke length and for polishing max. number of strokes 8.000 min 4 - 5 mm/s Vibration load according to ISO 8662-1 and ISO 8662-12 (measured at a max.
- Page 8 Daily maintenance Remove the protective hood (5.2 /1). Apply a couple of drops of oil, Diprofil FNA-K type (joke no. 0001287) or similar, to the needle bearing of the coupling piece (5.2/5) after approx. every 8 hours of use. Only loosen the clamping screw (5.2/2) far enough to ensure that the FMP-2 bearing bush is not lost.
- Page 9 Carefully clean the piston rod and tool holder (5.3/6) in addition to the tool holder protec- tive cap (5.3/5) with a soft cloth and WD 40 (joke no. 0580610 or 0580611) or similar and apply a few drops of oil, DIPROFIL FNA-K type (joke no.
- Page 10 Oberflächentechnik Surface Technology Technical data DIPROFIL FPT/ER ® Tool receptacle Ø 1.0 – 3.5 mm, insertion depth 32 mm Stroke length 0.5 – 6.0 mm infinitely adjustable Number of strokes 3.000 to 8.000 min Vibration* 4-5 m/s Noise level* < 70 db (A) Weight 600 g DIPROFIL...
- Page 11 Technology GmbH Service Department Oberflächentechnik Surface Technology Fax: 0 22 04 / 8 39 - 60 Sender: Company Name/Department Customer no. Street Postcode, town/city Please send us the spare parts drawing and the spare parts drawing for the following equipment: as a printout (see address overleaf), ...
- Page 12 Fax +49 (0) 22 04 / 8 39-60 Mail info@joke.de Web www.joke.de © Copyright joke Technology GmbH • July 2013 • All rights reserved for technical modifications, inaccuracies and printing errors. • Reprinting, even in part, only subject to prior written approval.