Panasonic CQ-C1001W Operating Instructions

Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
YFM284C450ZB TAMACO1104-1124 Printed in China
Preparation
Pull the insulation film out from Note: Battery Information:
the backside of the remote con- Battery Type: Panasonic lithium battery (CR2025) (Included
nly
trol gently. in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
The 24-hour system is used for the clock.
Clock Display at Power Off
1
Turn the ignition switch
Press [DISP] (Display) to change the display.
ACC
until the accessory indica- ON
tor lights.
Display off
2
Press [SRC] (PWR:
Power).
3
Press [DISP] (CLOCK).
4
Hold down [DISP] (CLOCK) for more than
2 seconds.
5
Adjust the hour.
[ ]: sets the hour ahead.
[ ]: sets the hour back.
6
Press [DISP] (CLOCK).
7
Adjust the minute.
[ ]: sets the minute ahead.
[ ]: sets the minute back.
8
Press [DISP] (CLOCK).
Notes:
"AdJ" is displayed before adjusting the clock.
Hold down [ ] or [ ] to change numbers rapidly.
CQ-C1121W/C1101W/C1001W
Operating Instructions
CQ-C1121W
MUTE
(CQ-C1121W)
Please read these instructions carefully before using this product and keep this manual for future reference.
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
If the replaced fuse fails, contact your nearest authorized Panasonic Service center.
Warning
Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit direct-
ly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Service Center.
Clock display
Anti-Theft System
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Caution
This face plate is not waterproof. Do not expose it to Do not touch the contacts on the face plate and the main
water or excessive moisture. unit, since this may result in poor electrical contact.
Do not remove the face plate while driving your car. If dirt or other foreign substances get on the contacts,
Do not place the face plate on the dashboard or nearby wipe them off with a clean and dry cloth.
areas where the temperature rises high.
Removing Mounting
1 1
Turn off the power. Slide the left side of the removable face
2
plate in place.
Press . The removable face plate will
2
open.
Press the right end of removable face plate
3
Pull it out toward you. until a "click" is heard.
Before Reading These Instructions
Panasonic welcomes you to our constantly growing family of electronic products owners.
CD Player/Receiver
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
This operating instruction manual is for 3 models CQ-C1121W, CQ-C1101W and CQ-C1001W. All illustrations throughout this
manual represent model CQ-C1121W unless otherwise specified. The following table describes the differences among 3 models.
Models
CQ-C1121W
Features
Volume control Rotary knob
Remote control function Yes (Included)
Pre-amp. output connector Rear/Front
Accessories
Operating Instructions Remote Control Unit
POWER
PWR PWR PWR MUTE MUTE MUTE
MODE MODE MODE VOL VOL VOL
(English: YFM284C450ZA)
(include a battery, only
TUNE
TRACK
(êÛÒÒÍËÈ: YFM284C451ZA) BAND BAND BAND
CAR AUDIO for CQ-C1121W)
( : YFM284C452ZA)
(EUR7641020)
(YFM284C453ZA : )
Q'ty: 1 set
Lock Cancel Plate
Installation Instructions
(FX0214C385ZA)
(YFM284C449ZA)
Q'ty: 1
Mounting Bolt
(YEJV014C002N)
Rubber Bushing
(YFS014C095ZA)
Notes:
The number in parentheses underneath each accessory part name is the part number for maintenance and service.
Accessories and their part numbers are subject to modification without prior notice due to improvements.
Mounting Collar and Trim Plate are mounted on the main unit at shipment. *
Safety Information
■
Read the operating instructions for the unit and all other compo-
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any prob-
lems resulting from failure to observe the instructions given in this
manual.
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
Warning
severe injury or death.
Warning
Observe the following warnings when using this
unit.
❑ The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driv-
er from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑ Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other bat-
tery systems, especially a 24 V DC battery system.
❑ Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the prod-
uct yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Center.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑ The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
❑ Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engi-
neer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
Specifications
General
Power supply : 12 V DC (11 – 16 V DC), negative
ground
Current consumption : Less than 2.2 A (CD mode; 0.5 W 4
channels)
Maximum power output : 50 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1121/C1101W)
: 45 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1001W)
Tone adjustment range : Bass: ±12 dB at 100 Hz, Treble: ±12
CQ-C1101W CQ-C1001W
dB at 10 kHz
: 4 – 8 Ω
Speaker impedance
Rotary knob Button
Pre-amp output voltage : 2.5 V (CD mode, 1 kHz, 0 dB)
: 200 Ω
Pre-amp output impedance
No No
Dimensions (W x H x D) : 178 x 50 x 160 mm
Weight : 1.3 k
Rear Rear
CD Player
Sampling frequency : 8 times oversampling
DA converter : 1 bit DAC System
Pick-up type : Astigma 3–beam
Light source : Semiconductor laser
Wave length : 790 nm
Frequency response : 20 Hz – 20 kHz (±1 dB)
Signal to noise ratio : 96 dB
Total harmonic distortion : 0.01 % (1 kHz)
Wow and flutter : Below measurable limits
Channel separation : 75 dB
Mounting Collar *
(FX0214C384ZA)
Q'ty: 1
Trim Plate *
(YFC054C081ZA:
Q'ty: 1
CQ-C1121/1101W)
(YFC054C079ZA: CQ-C1001W)
Q'ty: 1
Q'ty: 2
Power Connector
(YEAJ02877)
Q'ty: 1
Q'ty: 1
Q'ty: 1
■
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
Caution
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the mean- Observe the following cautions when using this
ings of the pictographs in order to use this manual and the system
unit.
properly.
❑ Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
This pictograph intends to alert you to the presence of
❑ This unit is designed for use exclusively in automo-
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in biles.
Caution
❑ Do not operate the unit for a prolonged period with the
injury or material damage.
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑ Do not expose the unit to direct sunlight or excessive
Observe the following warnings when installing.
heat.
❑ Disconnect the lead from the negative (–) battery termi-
Otherwise these will raise the interior temperature of the unit,
nal before installation. and it may lead to smoke, fire, or other damage to the unit.
❑ Do not use the product where it is exposed to water,
Wiring and installation with the negative (–) battery terminal con-
nected may cause electrical shock and injury due to a short circuit.
moisture, or dust.
Some cars equipped with the electrical safety system have specific
Exposure of the unit to water, moisture, or dust may lead to
procedures of battery terminal disconnection.
smoke, fire, or other damage to the unit. Make especially sure
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
that the unit does not get wet in car washes or on rainy days.
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
Observe the following cautions when installing.
INJURY OR DEATH.
❑ Never use safety-related components for installation, ❑ Refer wiring and installation to qualified service per-
grounding, and other such functions. sonnel.
Installation of this unit requires special skills and experience. For
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fix- maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
ing the product or its accessories.
❑ Installing the product on the air bag cover or in a location of the unit.
❑ Follow the instructions to install and wire the product.
where it interferes with airbag operation is prohibited.
❑ Check for piping, gasoline tank, electric wiring, and other Not following the instructions to properly install and wire the
product could cause an accident or fire.
items before installing the product.
❑ Take care not to damage the leads.
If you need to open a hole in the vehicle chassis to attach or wire
When wiring, take care not to damage the leads. Prevent them
the product, first check where the wire harness, gasoline tank, and
from getting caught in the vehicle chassis, screws, and moving
electric wiring are located. Then open the hole from outside if pos-
parts such as seat rails. Do not scratch, pull, bend or twist the
sible.
leads. Do not run them near heat sources or place heavy objects
❑ Never install the product in a location where it interferes
on them. If leads must be run over sharp metal edges, protect
with your field of vision.
the leads by winding them with vinyl tape or similar protection.
❑ Never have the power cord branched to supply other
❑ Use the designated parts and tools for installation.
equipment with power.
Use the supplied or designated parts and appropriate tools to
❑ After installation and wiring, you should check the nor-
install the product. The use of parts other than those supplied or
mal operation of other electrical equipment.
designated may result in internal damage to the unit. Faulty
The continuation of their using in abnormal conditions may cause
installation may lead to an accident, a malfunction or fire.
fire, electrical shock or a traffic accident. ❑ Do not block the air vent or the cooling plate of the unit.
❑ In the case of installation to an airbag-equipping car,
Blocking these parts will cause the interior of the unit to over-
confirm warnings and cautions of the vehicle manufactur-
heat and will result in fire or other damage.
er before installation.
❑ Make sure the leads do not interfere with driving or get-
ting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuiting.
Caution
THIS PRODUCT UTILIZES A CLASS LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
FM Stereo Radio
Frequency range : 87.5 MHz – 108 MHz
: 6 dB/µV (75 Ω)
Usable sensitivity
Frequency response : 30 Hz – 15 kHz (±3 dB)
Alternate channel selectivity : 75 dB
Stereo separation : 35 dB (1 kHz)
Image rejection ratio : 75 dB
IF rejection ratio : 100 dB
Signal to noise ratio : 62 dB
AM Radio
Frequency range :531 kHz – 1 602 kHz
Usable sensitivity : 28 dB/µV (S/N 20 dB)
Note:
Specifications and design are subject to modification without
notice due to improvements.
Some figures and illustrations in this manual may be different
from your product.
❑ Do not install the product where it is exposed to strong
vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
❑ Installation Angle
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑ Wear gloves for safety. Make sure that wiring is com-
pleted before installation.
❑ To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling the
battery for the remote control unit.
●
Use only specified battery (CR2025).
●
Match the polarity of the battery with the (+) and (–) marks in
the battery case.
●
Replace dead battery as soon as possible.
●
Remove the battery from the remote control unit when not using
it for an extended period of time.
●
Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
●
Dispose of the battery according to the local regulations.
●
Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
In case of battery leakage
●
Thoroughly wipe the battery liquid off the battery case and insert
new battery.
●
If any part of your body or clothing comes into contact with bat-
tery liquid, wash it with plenty of water.
●
If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.