Panasonic BT-LH900A Operating Instructions Manual page 19

MAIN MENU
(continued)
VIDEO CONFIG
Item Setting
GAMMA SELECT GPI For setting the gamma mode.
NORMAL GPI:
FILM
NORMAL: The normal gamma mode is
FILM:
FILM GAMMA OTHER This enables OTHER or VARICAM to be
VARICAM selected as the FILM setting for the
GAMMA SELECT item.
For the differences between OTHER and
VARICAM, refer to the graph below
showing the gamma characteristics curves.
COLOR TEMP. USER For setting the color temperature.
D93 USER: Any setting from 0 to 63 (equivalent
D65
D56
D93:
D65:
D56:
<Note>
The color temperature can be set for each
gamma mode (NORMAL, FILM).
SHARPNESS HIGH For setting the image sharpness.
MODE LOW HIGH: The images are accentuated with
LOW: The images are accentuated with
<Note>
The sharpness can be set for VIDEO and
all other input channels.
The underlined setting indicates the factory setting mode.
Description
This is the GPI setting. For
details, refer to "REMOTE
specifications" (page 23).
established.
The film mode that supports the
Varicam digital cine camera is
established. The actual film mode
setting can be changed using the
FILM GAMMA item listed next.
Input level
Normal gamma characteristics
OTHER characteristics
VARICAM characteristics
to a color temperature range from
3000 K to 9300 K) can be
established.
This is equivalent to a color
temperature of 9300 K.
This is equivalent to a color
temperature of 6500 K.
This is equivalent to a color
temperature of 5600 K.
fine edges.
thick edges.
Item Setting
SHARPNESS H 0 For setting the image sharpness in the
:
horizontal direction.
2
This item enables two settings, one for the
:
VIDEO input signals and one for other
30
signals, to be stored in the memory.
<Notes>
≥ While this item's setting is selected, the
≥ The sharpness can be set for VIDEO and
SHARPNESS V 0 For setting the image sharpness in the
:
vertical direction.
2
This item enables two settings, one for the
:
VIDEO input signals and one for other
30
signals, to be stored in the memory.
<Notes>
≥ While this item's setting is selected, the
≥ The sharpness can be set for VIDEO and
I-P MODE MODE2 For switching the IP conversion mode.
MODE1 MODE2: Movement compensation mode
MODE1: Normal mode
<Note>
This setting takes effect when progressive
signals (1080/30P, 1080/25P, 1080/24P,
720/60P, 720/50P or 480/60P) are input.
MONO GPI For selecting monochrome images.
OFF GPI:
ON
OFF: Normal images
ON:
<Notes>
≥ When RGB signals are input, the setting
≥ When ON has been selected as this
SD ASPECT GPI For setting the aspect ratio of the SD
16:9 signals.
4:3 GPI : This is the GPI setting. For details,
16:9 : The images are displayed with a
4:3 :
Description
only information displayed on the screen
is this item which appears at the bottom
left regardless of the MENU POSI setting
selected on the OSD screen.
all other input channels.
only information displayed on the screen
is this item which appears at the bottom
left regardless of the MENU POSI setting
selected on the OSD screen.
all other input channels.
This is the GPI setting. For details,
refer to "Concerning the REMOTE
specifications" (page 23).
Monochrome images
of this item is not reflected.
item's setting, the setting for the
CHROMA image control is fixed at 0.
When the setting is returned to OFF, the
CHROMA setting prior to the change is
restored.
refer to "REMOTE specifications"
(page 23).
16:9 aspect ratio.
The images are displayed with a 4:3
aspect ratio.
19