Related Manuals for Ryobi RLM4617ME
Summary of Contents for Ryobi RLM4617ME
- Page 1 RLM4617ME PETROL LAWN MOWER Original Instructions Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining this machine.
-
Page 2: General Safety Rules
Thank you for buying a Ryobi lawn mower. ■ Do not mow near drop-offs, ditches, excessively steep Your new lawn mower has been engineered and slopes, or embankments. Poor footing could cause a manufactured to Ryobi’s high standard for dependability, slip and fall accident. - Page 3 deterioration. Any damage may cause objects to be ● after striking a foreign object; inspect the product thrown towards the operator. for damage and make repairs as necessary before restarting and operating the product. ■ Replace worn or damaged parts before operating the ●...
- Page 4 SYMBOLS Important: Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOLS EXPLANATION Precautions that involve your safety. To reduce the risk of injury, user must read and understand operator’s manual before using this product.
- Page 5 Push the primer bulb 3 times. Set the throttle lever to max down against the handle. Pull the starter cord until the engine runs. Rear grass catcher Mulching plug option (mulching plug sold separately) The guaranteed sound power level is 94 dB. The guaranteed sound pressure level is 82 dB. Regulatory Compliance Mark (RCM).
-
Page 6: Intended Use
INTENDED USE WARNING This product is intended for domestic lawn mowing. The To avoid serious personal injury, do not attempt cutting blade should rotate approximately parallel to the to use this product until you read thoroughly and ground over which it is being wheeled. All four wheels understood completely the operator’s manual. -
Page 7: Operation
17. Wave washer inner side of the top cover. 18. Blade 2. Snap together the top and bottom parts of the grass 19. Bolt catcher. 20. Fuel tap closed (off) 21. Fuel tap open (on) INSTALLING THE GRASS CATCHER 22. Ground side NOTE: When using the grass catcher, do not install the 23. - Page 8 WARNING WARNING After fuelling, never tilt the product more than 25 degrees Never start or run the engine inside a closed or poorly for this could result in fuel leakage and risk of fi re. ventilated area; breathing exhaust fumes can kill. NOTE: Always use unleaded petrol with an octane rating Pre-checks of 91 or higher.
-
Page 9: Maintenance
■ New or thick grass may require a narrower cut path. SETTING THE BLADE HEIGHT See fi gure 6. ■ Clean the underside of the mower deck after each use to remove grass clippings, leaves, dirt, and any other When shipped, the wheels on the product are set to a low- accumulated debris. -
Page 10: Spark Arrestor
plastics are susceptible to damage from various types Replacement blades, bolts and washer can be ordered of commercial solvents. Use clean cloths to remove through the Bunnings special orders desk. dirt, dust, oil, and grease. ■ Replacement blades, bolts and washer can be ordered WARNING through the Bunnings special orders desk. - Page 11 fi lter elements can be ordered through the Bunnings special orders desk. The 5. Measure plug gap. The correct gap is 0.028 − 0.031 in. Ryobi part number for Australia and New Zealand is To widen gap, if necessary, carefully bend the ground 17150Z03011000.
- Page 12 WARNING Do not store the product with petrol in the tank inside a building where fumes may reach an open fl ame or spark. 2. If not using fuel stabilizer, allow the engine to run until the product is completely out of petrol. 3.
-
Page 13: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Handle not in cor- Handle positioned incorrectly. Check to be sure that lower part of handle is pushed fully back rect position. and snapped into proper position. Handle knobs not tightened. Tighten handle knobs. M o w e r n o t No petrol. - Page 16 Techtronic Industries (Australia) Pty. Ltd. 31 Gilby Road, Mt Waverley, VIC 3149, Australia Techtronic Industries New Zealand Ltd. 2 Landing Drive, Auckland Airport, Mangere, New Zealand 2022 20150828v2...