Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for OneRemote 34016102
Summary of Contents for OneRemote 34016102
-
Page 1: User Manual
OneRemote converter Type 34016102 User Manual Operate with Beolink Viasat HD Pace 460NV Pace 830NV Pace 850NV Pace 855NV Pace 865NV Samsung DSB-H670 Samsung SMT-S5140 Samsung SMT-S7140 Strong SRT-6750 Strong SRT-6752 Strong SRT-6765 Strong SRT-6780 34016102u3uk... -
Page 2: Beo4/ Beo5 Translation Table
Everyday use Beo4, Beo5, Beo6, Beoone Playback & Recording Play press 1 second. Alternative play. Stop *2 *1 *2 *1 Pause Rewind Back Forward Setup Record TV-Radio Other operations Media List info Ticket Exit Planner Help/ Options Power off *1 It is possible to exchange the up/ down arrow the functions with Power manual the blue and yellow buttons. - Page 3 Congratulations. The BEE2 converter from www.oneremote.dk can fully operate your device using your Bang & Olufsen remote control terminal, in a beelink system. Beo4 Beo5 or Beo6 remote controls can be used. Beolink 1000 can be used with reduced functionality. This guide explains how.
-
Page 4: Table Of Contents
List of Contents Beo4/ Beo5 Translation table ................page beeLINK basics ....................... page beeLINK2 installation ..................... page beeLINK2 connections ................... page Programming Zap option ..................page Menu option ......................page Beolink 1000, Beo4, Beo5 and Beo6 ..............page Beelink Active option ..................... page w w w . -
Page 5: Beelink Basics
IR-receiver in the room, this can also be used to feed the BeeLINK bus. Normally there is no need for two IR receivers in the same room. Data received by the IR-receiver is fed to a OneRemote Link Amplifier with built-in power supply and 5 outputs for beeLINK devices. -
Page 6: Beelink2 Installation
beeLINK2 installation The beeLINK2 controller gets its power supply and control data, via the CAT5 cable from a beeLINK amplifier. The beeBus. Once connected to the beeBUS the beeLINK2 controller only needs an IR-emitter to operate the device it has been designed for. The IR-emitter emits the same IR data as the device’s own remote control. Emitted IR data is in fact pure light at a frequency just out of the spectrum that the human eye is able to see. - Page 7 This is done using special IR-emitters that either measures the status signal on a TV-scart output or the presence of a video signal. OneRemote 81108180 IR-emitter cable. OneRemote 31108182 IR-emitter cable. Measures the DC-status on a Scart TV-output.
-
Page 8: Beelink2 Connections
Bee2 connections The IR/ sense socket is output for the IR-emitter that sends IR to the device to be operated. In some cases this socket is also used for sensing purposes. Some BeeLINK2 converters needs to know if the device is powered up or not. -
Page 9: Programming Zap Option
If the user would give it a fair chance, trying out the OneRemote layout, it is not likely that he would make use of this option. The OneRemote layout adds much perspective to many OSD menus on many devices, and makes sense once fully understood. -
Page 10: Beolink 1000, Beo4, Beo5 And Beo6
Beolink 1000 Compares to Beo4/ Beo5 ------------------- -------------------------------- VTAPE2 /VMEM2 /DVD2 / CDV AMEM2 For compatibility with older remote controls, a typical OneRemote layout uses the following buttons: Beolink 1000 Typical BeeLINK use ---------------- ----------------------------------------- Back, Backup e.t.c. EPG, Guide e.t.c. -
Page 11: Beelink Active Option
BeeLINK Active option. As all converters on the BeeLINK bus are receiving the IR-data simultaneously, every controller must know when to go active and when to go inactive. Sometimes two or more controllers are active at the same time. A BeeLINK 2 controller is used to operate a TV, a satellite receiver, a DVD-player, a projector or similar devices. Each controller is specifically made for one device.