3 Troubleshooting Guide CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY Motor fails to rotate. Power cord Chech power cord continuity between If there is no continuity, replace the (no noise is heard at all) pliug pins cord reel patition unit. cord reel patition unit.
4 Disassembly and Assembly Instructions Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner. Remove the power plug from the outlet. 4.1. Dust cover assembly 4.2. Separate the upper and lower removal body units 1. Open the dust box cover assembly at an angle of approx. 1.
3. Lift the upper body U to separate it from the lower body U. 2. Remove the switch lever. (There are no switch levers on the CG461.). 4.3. Printed circuit board removal 1. Remove the Control knob U, supporter plate U and switch cover U.
Page 8
3. Disengage the fast-on terminal of the lead wire (red) lead- 4. Remove the fast-on terminal of the lead wire (gray and ing to the fuse and that of the lead wire (blue) leading to orange) connecting the switch to the printed circuit board. the cord reel connected to the printed circuit board.
* For removing the printed circuit board AU on the 5. Lift the motor set section from the lower body U. CG461, first remove the fast-on terminal for the con- * CG467,CG465,CG463 necting section for the motor. * CG461 4.4. Motor removal 1.
4.5. Cord reel partition unit replace- 6. Remove all components fitted to the motor. a. Remove the motor support rubber (front). ment b. Remove the motor support rubber (rear). c. Remove the motor support. 1. Increase the gap width between the cord reel and the d.
4.6. Rail base U replacement 4.8. How to disassemble the tur- bine nozzle 1. Remove the screw fixing the rail base U onto the cord reel partition U. 4.8.1. Agitator ass'y 2. Remove the rail base U from the cord reel partition U. 1.
Page 12
4.8.3. Turbine complete 1. Pull up the floor nozzle pipe U and remove the turbine complete. (Fig.21) 4.8.4. Removal of the floor nozzle brush CU.DU.EU.FU 1. Turn the floor nozzle lower unit over. Insert the tip of a flat-blade screwdriver into one side of the brush, then remove the brush.(Fig.22) * For assembly, fit every component onto the floor nozzle lower unit.
6.4. PARTS LIST (BODY UNIT) Ref. No. Part No. Part Name & Description Remarks AMC93K-YZ0CE DUST COVER ASS'Y MC-CG467.CG467K Sherbet Blue AMC93K-YM0SE DUST COVER ASS'Y MC-CG465.CG465K Silver AMC93K-YN0KE DUST COVER ASSEMBLY MC-CG463.CG463K Black AMC93K-YP0RE DUST COVER ASSEMBLY MC-CG461.CG461K Burgundy AMC92L-YZ0CE DUST COVER MC-CG467.CG467K Sherbet Blue...
Page 18
Ref. No. Part No. Part Name & Description Remarks AMC10K-YP0VE BAG SUPPORTER AMC34D-YP00E SPRING A AMC73K-YP00E DUST BOX PACKING AMC99C-YM00E WHEEL MC-CG467.CG467K.CG465.CG465K AMC01C-YP0VE WHEEL MC-CG463.CG463K MC-CG461.CG461K AMC76B-YP0VE HANDLE COVER AMC97A-YP0VE LOWER BODY UNIT MC-CG467.CG467K CG465.CG465K CG463.CG463K AMC03A-YP0VE LOWER BODY MC-CG461.CG461K.