Table of Contents
Advertisement
Available languages
Available languages
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
220/240
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Removing and fitting a cutting disc (fig. B)
Cutting discs with a bore of 25,4 mm (standard)
• Press and hold down the spindle lock (5).
• Rotate the cutting disc until it locks.
• Using the spanner supplied, release the disc
retaining bolt (10) and remove it completely with
the outer retaining flange (11).
• Release the spindle lock (5).
• Replace the cutting disc and secure it with the
outer retaining flange (11) and the disc retaining
bolt (10).
Clamping the workpiece in position (fig. A)
Your D
WALT chopsaw is equipped with a quick-
E
adjusting material clamp (6).
Clamping materials with a maximum width of 110
mm (fig. C)
• Pull lever (13) in the direction of arrow (14).
• Push the clamp shaft (15) forward until jaw (16) is
almost touching the workpiece to be cut.
15
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Press lever (13) in the direction of arrow (17) until
it engages with the clamp shaft (15).
• Rotate the handle (18) clockwise and clamp the
workpiece securely.
• To release the workpiece, rotate the handle (18)
counterclockwise.
Clamping materials with a maximum width of 230
60
mm (fig. D)
• Loosen the two bolts (19) using the spanner
6
10
supplied with the tool.
15
• Slide fence (20) as far as necessary.
20
• Tighten the two bolts (19).
25
-
-
-
6
6
6
6
15
15
Adjusting the angle of cut (fig. D)
20
This D
WALT chopsaw can be used for left and right
E
-
mitre cuts up to 45°.
• Loosen the two bolts (19) using the spanner
supplied with the tool.
• Adjust the fence (20) to the required angle. When
turning the fence in the direction of arrow (21),
line up the scale with the right-hand side of the
slot (23). When turning the fence in the direction
of arrow (22), line up the scale with the left-hand
side of the slot (23).
• Tighten the two bolts (19) and clamp the
workpiece securely.
Instructions for use
• Always observe the safety instructions
• Do not apply excessive pressure to the
• Avoid overloading. Should the tool
Prior to operation:
• Install the appropriate cutting disc. Do not use
excessively worn discs. The maximum rotation
speed of the tool must not exceed that of the
cutting disc.
When cutting square or rectangular
section material, position the material
slightly off-centre towards the rear of the
tool.
and applicable regulations.
tool.
become hot, let it run a few minutes
under no load condition.
E N G L I S H
en - 4
Hide quick links:
Advertisement
Chapters
Table of Contents
