Dust Extraction; Optional Accessories; Protecting The Environment - DeWalt DW721KN Original Instructions Manual

2. Loosen the locking screws (a5) (fig. 50, 51).
3. Using an hex key, slightly rotate the bearings (a6) until lateral
movement has been neutralised (fig. 52).
4. Retighten the locking screws (a5) ensuring that the head
automatically goes into the rest position.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade. Remove the
jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.

Dust Extraction

WARNING: Always connect a dust extraction device
designed in accordance with relevant regulation regarding
dust emission. The air velocity of external connected system
shall be 20m/s +/–2m/s. Velocity to be measured in the
connection tube at the point of connection, with the tool
connected but not running.
Transporting
To transport the machine be sure the saw head is safely locked. Please
be aware the table is not suitable to lift the machine up. Always use
a fork-lift for transporting. For safe lifting set the fork under the lower
cross-bar of the leg-stand.

Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the appropriate
accessories.
Recommended saw blade DW721 / DW722 - DT4303

Protecting the Environment

Separate collection. This product must not be disposed of
with normal household waste.
WALT, recommended
E
Should you find one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D WALT office at the address indicated in this
E
manual. Alternatively, a list of authorised D
full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
GUARANTEE
D WALT is confident of the quality of its products and offers
E
an outstanding guarantee for professional users of the
product. This guarantee statement is in addition to and in no
way prejudices your contractual rights as a professional user
or your statutory rights as a private non-professional user. The
guarantee is valid within the territories of the Member States of
the European Union and the European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT tool, simply return it within 30 days, complete with all
E
original components, as purchased, to the point of purchase,
for a full refund or exchange. The product must have been
subject to fair wear and tear and proof of purchase must be
produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
the 12 months following purchase, you are entitled to one
service free of charge. It will be undertaken free of charge at
an authorised D WALT repair agent. Proof of purchase must
E
be produced. Includes labour. Excludes accessories and spare
parts unless failed under warranty.
• ONE YEAR FULL WARRANTY •
If your D WALT product becomes defective due to faulty
E
materials or workmanship within 12 months from the date of
purchase, D WALT guarantees to replace all defective parts
E
free of charge or – at our discretion – replace the unit free of
charge provided that:
• The product has not been misused;
• The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorised
persons;
• Proof of purchase is produced.
• The product is returned complete with all original
components
If you wish to make a claim, contact your seller or check the
location of your nearest authorised D
the D WALT catalogue or contact your D
E
address indicated in this manual. A list of authorised D
repair agents and full details of our after-sales service is
available on the Internet at: www.2helpU.com
ENGL ISH
WALT product needs replacement,
E
WALT
E
WALT repair agents and
E
WALT tool, in
E
WALT repair agent in
E
WALT office at the
E
WALT
E
35