Allgemeine Sicherheitshinweise WARNUNG Bitte lesen Sie die folgenden Sicherheitshinweise: Wasser, Flüssigkeiten, Feuchtigkeit: Das Gerät soll nicht in der Nähe von Wasser- oder Flüssigkeitsquellen benutzt werden. Das Gerät soll nicht in Bereichen grosser Feuchtigkeit betrieben werden. Achten Sie darauf, dass das Gerät nicht in Flüssigkeiten fällt, oder dass Flüssigkeiten durch die Gehäuseöffnungen eindringen können.
Das Erde / Masse Konzept DIGITAL transformer balanced output ANALOG transformer balanced output Ground Lift Jumper: XLR male XLR male G(round) L(ift) C(ase) DIGITAL transformer balanced input ANALOG transformer balanced input Ground Lift Jumper: XLR female XLR female G(round) L(ift) C(ase) DIGITAL unbalanced output ANALOG electronically balanced output...
Page 4
Anschluss / Steckerbelegung für analoge Signale ANALOGE SIGNALE Symmetrisches Kabel (Signal) an (Trafo)symmetrischen Eingang XLR MALE PLUG Shield / Abschirmung = Signalmasse = Pin 1 Hot / + Phase = Pin 2 Cold / - Phase = Pin 3 Das Steckergehäuse sollte nicht mit der COLD Abschirmung des Kabels verbunden werden.
ALLGEMEINES DIE STROMVERSORGUNG ANA-TOOL F8xx in ihren verschiedenen Aus- Die Stromversorgung erfolgt über eine einge- führungen ist eine achtkanalige Einheit (vier- baute IEC-CEE-Dose. Wenn nötig, kann die kanalig auf Anfrage) zum Aufholen, Anpassen, Netzspannung intern von 230 V auf 115 V Impedanz ändern, Symmetrieren und Desym- umgestellt werden.
Page 6
UNSYMMETRISCHER EINGANG - SYMMETRISCHER AUSGANG (sofern Modul vorhanden) DIE EINGÄNGE nicht kurzgeschlossen werden, sondern muss offen bleiben. Die rückseitigen unsymmetrischen Eingänge Bei unsymmetrischem Abschluss stellt sich ein sind als vergoldete Cinch-Buchsen ausgeführt. Pegelverlust von 6 dB ein. (siehe auch Seite 4) Sie verfügen über eine numerische- (1 ...
Page 7
SYMMETRISCHER EINGANG - UNSYMMETRISCHER AUSGANG (sofern Modul vorhanden) DIE EINGÄNGE OPTION Die rückseitigen symmetrischen Eingänge sind Optional kann das Gerät mit hochwertigen als vergoldete XLR-Buchsen ausgeführt. Sie ZFT´s = Zero-Field-Transformatoren im Ein- verfügen über eine numerische- (1 ... 4) sowie gang ausgerüstet werden.
General Safety Instructions WARNING For your protection, please read the following: Water, Liquids, Moisture: This appliance should not be used near water or other sources of liquids. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. Power Sources: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
The Earth / Grounding Concept DIGITAL transformer balanced output ANALOG transformer balanced output Ground Lift Jumper: XLR male XLR male G(round) L(ift) C(ase) DIGITAL transformer balanced input ANALOG transformer balanced input Ground Lift Jumper: XLR female XLR female G(round) L(ift) C(ase) DIGITAL unbalanced output ANALOG electronically balanced output...
Page 10
Connection / Connectors for Analog Signals ANALOG SIGNALS Balanced Cable (Signal) to (Transformer) Balanced Input XLR MALE PLUG Shield = Signal Ground = Pin 1 Hot / + Phase = Pin 2 Cold / - Phase = Pin 3 The case of the connector should not be wired COLD to the shield of the cable.
GENERAL THE POWER SUPPLY ANA-TOOL F8xx in its different appearances is Mains is connected via a built-in IEC-CEE a eight-channel unit (four-channel on request) mains socket. If necessary, mains voltage can for gain make-up, impedance matching, balan- be internally altered from 230 to 115 V. cing and unbalancing of general audio signal The "POWER"-switch is situated on the front sources.
Page 12
UNBALANCED INPUT – BALANCED OUTPUT (if this Modul is present) THE INPUTS HINT In case of unbalanced termination of the elec- The back mounted unbalanced inputs appear tronically balanced outputs, pin 3 of the XLR as gold plated cinch connectors. They are connector may not be shortened but must be marked numeric (1 ...
Page 13
BALANCED INPUT - UNBALANCED OUTPUT (if this Modul is present) THE INPUTS OPTION The inputs feature gold plated XLR-type As an option the unit may be equipped with connectors. They are situated on the rear of high quality ZFT = Zero-Field-Transformers in the unit and marked numeric (1 ...
Page 14
TECHNICAL DATA ANA-TOOL F810 / F811 / F812 / F820 / F822 All measurement RMS unweighted, 20 Hz - 20 kHz, relativ to 6 dBu, Gain = 1, as not otherwise noted, values in brackets [ ] referred to transformer balanced outputs.
PCB LAYOUT AND JUMPER SETTING ANALOG MODULE 1 4 x unbalanced Ins to balanced Outs Pin 1 from XLR socket C-L-G connected to internal Ground-Plane. (ex Works setting) Pin 1 from XLR socket C-L-G lifted. Pin 1 from XLR socket C-L-G connected to case.
KONFORMITÄTSERKLÄRUNG CONFORMITY STATEMENT Wir bestätigen hiermit, dass das folgende Gerät: We herewith declare that the following unit: Bezeichnung: ANA-TOOL F810 / F811 / F812 Name : ANA-TOOL F810 / F811 / F812 F820 / F822 F820 / F822 Serien Nr. :...