Objecto T3 User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

USER MANUAL

Table of Contents

Summary of Contents for Objecto T3

Page 1 USER MANUAL...
Page 2: Safety Information
English Safety Information This section presents important safety information. Always follow these instructions when using • the product. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Read all instructions before using this heater.
Page 3 English 14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 15. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet.
Page 4 After use, be sure to turn off the power, and unplug the power cord from the outlet. When cleaning the product, for safety's sake be sure to unplug it from the outlet. Do not plug or unplug the product while your hands are wet. Never use in a location that produces flammable or corrosive gases, or where they accumulate.
Page 5 English Names of Parts and Their Functions Front Control Panel Back Reset button Heat grill Handle Power switch Body Power cord Power plug Bottom Air intake Temperature sensor Filter Accessories Remote control × 1 Coin-shaped lithium battery (CR2025) × 1...
Page 6 English *About Safety Features • If the heater falls over during use, it activates the tip over switch, turning the power off. • If the heater gets too hot, it activates the thermostat and automatically shuts it off (To resume the operation, press the Reset button on the rear after it cools down).
Page 7: Correct Usage
English Correct Usage Control Panel Child lock indicator lamp Remote control Display receiver Mode indicator Child lock button Power button Mode switch Temperature OFF-timer button button setting button Transmitter OFF-timer button Temperature setting button Mode switch button OFF button...
Page 8: Starting And Stopping Operation
English Starting and Stopping Operation Turn on the power switch button located on the lower-right and back of the heater. The heater beeps and "--" is displayed on the control panel. <Display> Press the Power button on the heater to start operation. It starts operating in the LO (low) mode.
Page 9 English Once the desired temperature is displayed, simply stop pressing the button (remote control ). After about 10 seconds, the displays switches from a flashing mode to a solid one. When the temperature in the room drops below the set temperature, the heater starts working and stops only when it reaches the set temperature.
Page 10: Using The Child Lock
English To change the time on the timer Press the OFF-timer button (remote control ) until the desired shutdown timer setting is shown. Using the Child Lock This function prevents children from accidentally changing the settings. Child lock indicator lamp Child lock button While the heater is operating, press and hold the child lock button (5 seconds or more).
Page 11: Cleaning And Storage
English Keep the heater an appropriate distance from walls and surrounding objects (to avoid causing a ﬁre). At least 40 inches above At least 40 inches to the right At least 40 inches to the left At least 40 inches behind At least 3 feets in front Cleaning and Storage Cleaning the Heater...
Page 12: Replacing Filters
English Cleaning the Air Intake (Once a week) (1) Turn the heater over so the air intake can be seen. (2) Thoroughly remove any dust or debris by hand or a vacuum cleaner from the intake filter. (3) Remove the filter from the air intake and thoroughly remove any dust or debris by hand or a vacuum cleaner.
Page 13: Before Using The Remote Control
English Setup Place the heater on a level surface. Place on a flat, stable surface. (See page 11) Make sure nothing flammable is nearby; if there is something flammable, move it before using the heater. When moving the heater, you may hear a rattling sound; this is the tip-over switch (safety device) and it is normal for it to make noise.
Page 14 English Check the following before Requesting Repair or Service Problem Primary cause Solution The power does not • The power cord is not Plug the power cord into the outlet. turn on. plugged into the outlet. • Not located in a flat Check the location and locate the stable location (tip over unit in a flat, stable location.
Page 15: Specifications
English Specifications Product name T3 Panel Heater Model HR-36 Power supply 110 – 120 V AC, 50/60 Hz Power consumption HI 1,000W LO 500W Tip-over switch (internal type), thermal fuse, thermostat Safety features Approx. 71 inches Power cord length Approx. 26 × 7 × 17 inches External dimensions Approx.
Page 16: Limited Warranty Policy
Should service be necessary for any reason due to manufacturing defect or malfunction during the 90 days period, OBJECTO will provide carry-in repair service at our FACTORY SERVICE CENTER at no charge, and for the duration of the extended 9 months parts warranty period will replace the defective part only, not including labor, provided the defect or malfunction is veriﬁ...