Maintenance; Ec Declaration Of Conformity - EGO ST1500E Operator's Manual

NOTICE:
Always clean the spool retainer, spool and spool
base before reassembling the trimmer head. Check the
spool retainer, spool and spool base for wear. If necessary,
EN
replace the wear parts.
NOTICE:
Failure to wind the line in the direction indicated
will cause the trimmer head to operate incorrectly.
Install a pre-wound spool
Press the two release tabs on the spool base and pull the
spool retainer out (Fig. S). Then place a pre-wound spool
on the retainer with notches aligned with retainer eyelets
(Fig. X). Lastly, align the retainer slots with the tabs on the
spool base and press the retainer evenly down, ensuring
that it snaps into place (Fig. W).
Fig. W & X parts description see below:
W-1 Tab
W-2 Slot
NOTICE:
Make sure that the tabs on the spool base snap
into place or the spool will come out during operation.

MAINTENANCE

WARNING: When servicing, use only identical
replacement parts. Inspect and maintain the machine
regularly. To ensure safety and reliability, all repairs
should be performed by a qualified service technician.
WARNING:
Battery tools do not have to be plugged
into an electrical outlet; therefore, they are always in
operating condition. To prevent serious personal injury,
take extra precautions and care when performing
maintenance, service or for changing the cutting
attachment or other attachments.
WARNING:
To prevent serious personal injury,
remove the battery pack from the tool before servicing,
cleaning, changing add-on attachments or removing
material from the unit.
CLEANING THE UNIT
Clean the unit using a damp cloth with a mild detergent.
Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by certain
aromatic oils, such as pine and lemon, and by solvents
such as kerosene. Moisture can also cause a shock
hazard. Wipe off any moisture with a soft dry cloth.
Use a small brush or the air discharge of a small
vacuum cleaner brush to clean the air vents on the rear
housing.
12
56 VOLT LITHIUM-ION CORDLESS STRING TRIMMER — ST1500E
STORING THE UNIT
Protecting the environment
X-1 Notch
X-2 Eyelet

EC DECLARATION OF CONFORMITY

We, CHERVON EUROPE LTD.
47 CASTLE STREET, READING, RG1 7SR, UNITED KINGDOM
Declare that the product 56V lithium-ion cordless
string trimmer ST1500E complies with the essential
health and safety requirements of the following Directives:
2006/42/EC, 2004/108/EC, 2011/65/EU, 2000/14/EC
Standards and technical specifications referred to:
EN 60335-1, EN 50636-2-91, EN ISO 11806-1,
EN ISO 12100, EN 62233, EN 55014-1, EN 55014-2
Measured Sound Power Level: 89.34 dB(A).
Guaranteed Sound Power Level: 93.0 dB(A).
Vice President of Chervon Europe
* (Authorized representative for CHERVON and responsible for technical documentation)
01/01/2016
Remove the battery pack from the string trimmer when
it is not in use.
Clean the tool thoroughly before storing it.
Store the unit in a dry, well-ventilated area, locked-up
or up high, out of the reach of children. Do not store
the unit on or adjacent to fertilizers, petrol, or other
chemicals.
Do not dispose of electrical equipment,
battery charger and batteries/rechargeable
batteries into household waste!
According to the European law 2012/19/
EU, electrical and electronic equipment
that is no longer usable,and according to
the European law 2006/66/EC, defective
or used battery packs/batteries, must be
collected separately.
If electrical appliances are disposed of in
landfills or dumps, hazardous substances
can leak into the groundwater and get into
the food chain, damaging your health and
well-being.
Peter Melrose
Quality Manager of Chervon
Dong Jianxun