Advertisement
DIAGRAM OF THE CONSOLE
¥ Misuse of this treadmill may cause serious injury. ¥ Do not stand on
walking belt when starting treadmill. ¥ Read User's Manual and follow
warnings and operating instructions. ¥ Keep fluids off electronic console.
Clip
Speed Control
CAUTION:
Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turning
on the power.
¥ Always wear the clip (see the drawing above)
whilst using the treadmill. When the key is re-
moved from the console, the walking belt will
stop.
BATTERY INSTALLATION
The console requires three "AA" batteries (not in-
cluded). Alkaline batteries are recommended.
To install batteries, open the battery cover under the
console as shown below. Press three batteries into the
battery com-
partment.
Make sure
Battery
that the neg-
Cover
ative (Ð)
ends of the
batteries are
touching the
springs.
Close the
Batteries
battery cover.
8
Monitor Displays
Key
¥ Adjust the speed in small increments.
¥ The training zones marked beside the speed
control are general guidelines only. See pages
14 and 15 for more information.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console. Use only a sealed water bottle.
STEP BY STEP CONSOLE OPERATION
If there is a thin sheet of clear plastic on the face of the
console, remove it.
Before operating the console, make sure that the power
cord is properly plugged in. (See HOW TO PLUG IN
THE POWER CORD on page 7.)
Next, step onto the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
Follow the steps on page 9 to operate the console.
Insert the key fully into the power switch.
1
Inserting the key will
not turn on the dis-
plays. The displays will
turn on when the
ON/RESET button is
pressed or when the
walking belt is started.
Note: If you just in-
stalled batteries, the displays will already be on.
Reset the speed control.
2
Slide the speed control
down to the RESET po-
sition. Note: Each time
the walking belt is
stopped, the speed
control must be moved
to the RESET position
before the walking belt
can be restarted.
Start the walking belt.
3
After you have moved the speed control to the
RESET position, slowly slide it upward until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin exer-
cising. Change the speed of the walking belt as de-
sired by sliding the speed control.
To stop the walking belt, step onto the foot rails and
slide the speed control to the RESET position.
Follow your progress with the monitor displays.
4
TIME displayÑThis
display shows the total
time that you have
walked or run on the
treadmill.
DISTANCE displayÑ
This display shows the
total distance that you
have walked or run.
SPEED displayÑThis
display shows the speed
of the walking belt.
CALORIES/FAT
Arrows
CALORIES displayÑ
This display shows the
approximate numbers of
calories and fat calories
you have burned. (See
FAT BURNING on page
14 for an explanation of fat calories.) Every seven
seconds, the display will change from one number
to the other. Arrows in
the display will indicate
which number is cur-
rently shown.
The displays can be
reset, if desired, by pressing the ON/RESET button.
5
When you are finished exercising, stop the
walking belt and remove the key.
Step onto the foot rails, stop the walking belt, and
remove the key from the console. Store the key in a
secure place. After the key is removed, the dis-
plays will remain on for about five minutes.
Note: Any time that the walking belt is stopped
and no console buttons are pressed for five
minutes, the displays will automatically turn off
in order to conserve the batteries.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
The incline of the treadmill can be changed by raising
or lowering the back end. Before changing the in-
cline, remove the key and unplug the power cord.
Hold the
rear roller
cover with
both
hands.
When the
back end
Hold the Rear
of the
Roller Cover
Incline
treadmill is
in these locations
Leg
in the low-
est posi-
tion, the incline is about 10%. Raise the back end until it
clicks into position. (Note: It may be necessary to shake
the treadmill slightly so that it clicks into position.) The
incline will then be about 5%. Raise the back end again
until it clicks into position. The incline will then be about
3%. To lower the back end, first raise it past the highest
position, and then lower it. CAUTION: Before exercis-
ing, push on the back of the treadmill to make sure
that the incline legs are locked in position. Do not
place objects under the treadmill to change the in-
cline; change the incline only as described above.
9
Advertisement
