Lightsky series GLG L IGHT ING E QUIPM E NT CON TE NT S General information Safety instructions Trait and skill speci cations Operation panel Dimensional drawings Photometric data Mounting and Installation Power supply and Signal connection Display menu DMX traits 11.
GLG L IGHT ING E QUIPM E NT 1. GENERAL IN FOR MAT IO N INTRODUCTION: Congratulations, you have just purcha sed one of the most innovative and reliable LED xtures on the market today. Our company has been designed to perform reliably for y ears when the guidelines in this booklet are followed.
GLG L IGHT ING E QUIPM E NT 2. SAFETY IN STR UCT IO NS Notice: To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Our company will not accept responsibility for damages resulting from the misuse of this xture due to t he disregard of the information printed in this manual .
GLG L IGHT ING E QUIPM E NT 3. PERFORMANCE TRAIT AND SKILL S PEC IFICAT I ONS Voltage AC100~240V 50/60Hz. Power 246W. LED chip 10W RGBW 4 in 1 LED chip. LED QTY 18PCS. LED life 50000H. Beam angle Zoom function min.7°,max.55°.
Lightsky series GLG L IGHT ING E QUIPM E NT Other feature : 1.Extend IP address function , each IP address maxi m um can set 64 2.Support DMX signal priority identi cation, when lose the signal it would be turn into Black , default scene , Autom atic function etc according to your set.
GLG L IGHT ING E QUIPM E NT 7. MOUNTING AND I NS TALL ATI ON Cautions: For added protection mount the xtures in areas ou tside walking paths, seating areas, and away from areas were unau thorized personnel might reach the xture. Before mounting the xtur e to any surface, make sure that the installation area can hold a minimum point load of 10 times the device's weight.
GLG L IGHT ING E QUIPM E NT 8. POWER SUPPLY AND SIGNAL C ONN ECT I ON 1. Power supp ly Use the professional plug to connect the projector and main power supply. Please pay attention to the voltage, freque ncy the same as the mentioned on the projector.
Page 12
GLG L IGHT ING E QUIPM E NT speaking, DMX terminator is an XLR connector with a 120 1/2w resistor connected across pin 2 and 3.Which is then plugged into the output socket on the last projector in the chain. Refer to the connection as above:(Picture ).We suggest using the DMX signal di s tributor when the...
GLG L IGHT ING E QUIPM E NT 9. DISPLAY MEN U Menu Menu Menu SETTING Exit ww.goedlichtengeluid.nl info@goedlichtengeluid.nl...
Page 14
GLG L IGHT ING E QUIPM E NT Remark Menu Menu Menu Power on time ****H Fixture times Lamp on time ****H Fixture LAMP_TEM *** temperatures RDM UID 3888:******** 1. Dimmer 0-255 2. Dimmer ne 0-255 3. Shutter 0-255 4. Red-1 0-255 5.
Page 15
GLG L IGHT ING E QUIPM E NT Remark Menu Menu Menu 22.Fixture control 0-255 DMX live 23.Calibration 0-255 24.Slave ID 0-255 INFO LED_XY_SOFT:V*.** Version info LED_DPY_SOFT:V*.** Exit www.goedlichtengeluid.nl info@goedlichtengeluid.nl...
Page 16
GLG L IGHT ING E QUIPM E NT Remark Menu Menu Menu Menu Close Default P/T swap Open Close Default Pan invert Pan/Tilt Open Close Default Tilt invert Open Exit System reset Reset Exit Quick Open PERSON closedown Close P/T angle...
Page 17
GLG L IGHT ING E QUIPM E NT Remark Menu Menu Menu Menu English( Default Display language Chinese Light always Default 2 minutes Display sleep 4 minutes 6 minutes Display PERSON Display 10-100 intensity Default Display Normal rotation Rotate 180...
Page 18
GLG L IGHT ING E QUIPM E NT Remark Menu Menu Menu 1. Dimmer 0-255 2. Dimmer ne 0-255 3. Shutter 0-255 4. Red-1 0-255 5. Green-1 0-255 6. Blue-1 0-255 7. White-1 0-255 8. Red-2 0-255 9. Green-2 0-255 10.Blue-2...
Page 19
GLG L IGHT ING E QUIPM E NT Menu Menu Menu Menu Scene 0-100 1. Dimmer 0-255 2. Dimmer ne 0-255 3. Shutter 0-255 4. Red-1 0-255 5. Green-1 0-255 6. Blue-1 0-255 7. White-1 0-255 8. Red-2 0-255 9. Green-2 0-255 10.Blue-2...
Page 20
GLG L IGHT ING E QUIPM E NT Menu Menu Menu Menu Edit program 2 Same as Edit program1 Edit program 3 Same as Edit program1 Edit program 4 Same as Edit program1 Edit Edit program 5 Same as Edit program1...
Page 21
GLG L IGHT ING E QUIPM E NT Menu Menu Menu Menu Error list ±5.00% ±5.00% Tilt Calibration Lens ±5.00% Exit Factory default **** SERVICE default **** Calibration Time clean **** Factory Developer **** Machine sel **** Exit **** Updata Exit www.goedlichtengeluid.nl...
GLG L IGHT ING E QUIPM E NT 10 DMX T R AIT S Channel E ect values Dimmer 0-255 0-100 Dimmer ne 0-255 0-100 No function 10-49 4-19 Slow closing,Fast opening slow fast 50-89 20-34 Fast closing,Slow opening Slow...
Page 23
GLG L IGHT ING E QUIPM E NT Channel E ect values No function 2-225 1-88 Colour gradient change 226-230 89-90 2700K Macro 231-235 91-92 3200K colour 236-240 93-94 4200K 241-245 95-96 5600K 246-250 97-98 6500K 251-255 99-100 8000K 0-255...
Page 24
GLG L IGHT ING E QUIPM E NT Channel E ect values 149-239 59-93 No function Fixture 240-244 94-95 Pan Calibration control 245-249 96-97 Tilt Calibration 250-255 98-100 No function Calibration 0-255 0-100 All IDs are e cient lighting its own...
Page 25
GLG L IGHT ING E QUIPM E NT Channel E ect values ID is(4*n)+4 e ective,(n=0-15) 219-221 85-86 4 8 12 16 20…64 ID is(5*n)+1 e ective,(n=0-12) 222-224 87-88 1 6 11 16 21…61 ID is(5*n)+2 e ective,(n=0-12) 225-227 88-89 2 7 12 17 22…62...
Page 26
GLG L IGHT ING E QUIPM E NT Si mple Standard Extended1 Extended2 Function Dimmer Dimmer ne Shutter Red /Red-1 Green /Green-1 Blue /Blue-1 White/White-1 Red-2 Green-2 Blue-2 White-2 Red-3 Green-3 Blue-3 White-3 Macro colour Pan ne Tilt Tilt ne...
GLG L IGHT ING E QUIPM E NT 12. TROUBLE D I SPOSE It is recommended some solution for some normal tro uble shooting. Any inextricability problems should always be handl ing by the professional person. Disconnect the power supply be fore maintenance the light.
GLG L IGHT ING E QUIPM E NT 13. CLEANING AND M AI NTE NAN CE 1. In order to ensure the projector could work norm a lly. It should be kept clean always .The lens should also be regul arly cleaned to maintain an optimum light output.
Need help?
Do you have a question about the pastello zoom mkII and is the answer not in the manual?
Questions and answers