Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Brawn BGMF33
Summary of Contents for Brawn BGMF33
- Page 1 BGMF-SB SERIES...
- Page 3 OPERATION MAINTENANCE MANUAL BGMF-SB SERIES SERIAL NUMBER 1----- ___________________ CUSTOMER:____________________________ SALES REP.:____________________________...
- Page 7 * ALL DIMENSIONS AND WEIGHTS ARE FOR REFERENCE ONLY UNLESS THE DRAWING IS CERTIFIED. LOW PRESSURE * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, STUFFING BOX INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION.
-
Page 9: Table Of Contents
BRAWN Mixer product. Please direct these comments in writing to the National Sales Manager WARNING at BRAWN Mixer, Inc., located in Holland, Michigan. To expedite troubleshooting service, please make your initial To assure maximum safety, optimum performance, contact through your BRAWN Mixer Representative. -
Page 10: Initial Inspection
6. Wire the mixer motor in accordance with the 1. Upon receipt of your Brawn Mixer, check for possible nameplate wiring diagram and with local and national shipping damage. Report any damage immediately electric codes. -
Page 11: Start-Up
Drain regularly if storage atmosphere results in formation of condensation. INSTALLATION Installation must be handled by qualified service or maintenance personal. ELECTRIC MOTORS ELECTRIC MOTORS, Continued OPERATION Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 3 of 11 8/6/2015... - Page 12 The following maintenance procedures should be performed regularly: 1. Bearing lubrication (When regreaseable bearings are supplied) 2. Insulation resistance check 3. Cleaning Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 4 of 11 8/6/2015...
- Page 13 1. Stop the motor. Lock out the switch. 2. Thoroughly clean off pipe plugs and remove from housings. 3. Remove hardened grease from drains with stiff wire or rod. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 5 of 11 8/6/2015...
-
Page 14: Air Motors
DIRECTION DIAGRAM oil. If water has been detected in the motor, the bearings and seals should be replaced after drying out the motor. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 6 of 11 8/6/2015... -
Page 15: Maintenance
3. Install the pipe plug and supply a small amount of additional lubricant to ensure that all voids in the box are filled. GEARBOX OIL PLUG LOCATIONS Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 7 of 11 8/6/2015... -
Page 16: Specifications
An interlace braided 550° F 0-12 packing, made from a Your BRAWN Mixer has been furnished with either a special polyimide yarn that standard, seven-ring, stuffing box (see Figure 1), or a resists abrasion, yet does low-pressure, two-ring, stuffing box (see Figure 2), not score the shaft. -
Page 17: Seating The Packing
PACKING. maintenance schedule that is practical for your application. When making adjustments, do not tighten more than a quarter-turn, to avoid excessive friction. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 9 of 11 8/6/2015... -
Page 18: Storage
Phone: 616/399-5600 Fax 616/399-3084 REPLACING PACKING, Cont. STORAGE Units shipped from Brawn Mixer, Inc. are intended to be used within 30 days after receipt and presumed to be stored indoors in a heated building. Store mixers as packaged by the factory. If you intend storing units under adverse conditions or for a long period of time, special storage precautions will be necessary. -
Page 19: Warranty
ALL product must be received within 14 days of to or from BRAWN. In the case of components issuing an RGA number. purchased by BRAWN Mixer, Inc. and incorporated in the equipment, the component manufacturer's guarantee shall apply. - Page 20 UNLESS THE DRAWING IS CERTIFIED. BD/BGM HOUSING * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN EXPLODED VIEW HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION. DIMENSION AND ASSEMBLY DRAWING...
- Page 21 UNLESS THE DRAWING IS CERTIFIED. BD/BGM FIXED MOUNTING * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN ASSEMBLY HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION. DIMENSION AND ASSEMBLY DRAWING...
- Page 22 Plate mount w/shock absorbers 500075 $182 38 [BD(F)] Angle riser 500121 O-ring 10028602 NOTES Consult Factory: provide serial number with request for quotation. SPARE PARTS KIT Add $679 Shaded items = Recommended Spare Parts Kit Copyright 2015 BRAWN Mixer, Inc. 06/15/2015 Page 2-2...
- Page 23 – THIS PAGE IS INTENTIONALLY LEFT BLANK –...
- Page 24 – THIS PAGE IS INTENTIONALLY LEFT BLANK –...
- Page 25 – THIS PAGE IS INTENTIONALLY LEFT BLANK –...
-
Page 26: Th Avenue Holland, Mi
3389 128 AVE. HOLLAND, MI 49424 BRAWN MIXER SALES REPRESENTATIVES PHONE: 616-399-5600 FAX: 616-399-3084 UNITED STATES ILLINOIS (SOUTHERN) MISSOURI (EASTERN) OKLAHOMA WEST VIRGINIA (EASTERN) MID-STATES ENGINEERED EQUIP. MID-STATES ENGINEERED EQUIP. G.C. SOLUTIONS DATA DESIGN SERVICES 2244 ROSE LANE 2244 ROSE LANE P.O.
Need help?
Do you have a question about the BGMF33 and is the answer not in the manual?
Questions and answers