Page 3
OPERATION MAINTENANCE MANUAL BG SERIES SERIAL NUMBER ___________________ CUSTOMER:____________________________ SALES REP.:____________________________...
BRAWN Mixer product. Please direct these comments in writing to the National Sales Manager WARNING at BRAWN Mixer, Inc., located in Holland, Michigan. To expedite troubleshooting service, please make your initial To assure maximum safety, optimum performance, contact through your BRAWN Mixer Representative.
It is recommended that the shaft be spotted with a drill 1. Upon receipt of your Brawn Mixer, check for possible point at the setscrew locations to prevent loosening shipping damage. Report any damage immediately of the impeller(s).
5. Mixer position in tank should be as shown in FIGURE A or B [below] for maximum turnover of Do not attempt to start mixer with impellers buried liquid. in solids or solidified liquids FIGURE A FIGURE B Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 3 of 9 8/6/2015...
A wiring diagram is generally located on the conduit box of the motor. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 4 of 9 8/6/2015...
Page 14
½ hour before replacing operation of the equipment. Particular applications may drain plug. require further procedures 6. Put motor back in operation. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 5 of 9 8/6/2015...
On non-explosion-proof TEFC motors, a removable plug in the bottom center of the motor frame or housing permits removal of accumulated moisture. Drain regularly. AIR MOTOR ROTATIONAL DIRECTION DIAGRAM Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 6 of 9 8/6/2015...
If water has been detected in the motor, the bearings and seals should be replaced after drying out the motor. Copyright 2015 BRAWN Mixer, Inc. www.BRAWNMIXER.com Page 7 of 9 8/6/2015...
LUBRICATION STORAGE Although the gear box is considered “lubricated for life”, Units shipped from Brawn Mixer, Inc. are intended to be the oil level and condition should be checked periodically used within 30 days after receipt and presumed to be for signs of degradation.
ALL product must be received within 14 days of to or from BRAWN. In the case of components issuing an RGA number. purchased by BRAWN Mixer, Inc. and incorporated in the equipment, the component manufacturer's guarantee shall apply.
UNLESS THE DRAWING IS CERTIFIED. BD/BGM HOUSING * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN EXPLODED VIEW HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION. DIMENSION AND ASSEMBLY DRAWING...
Page 20
UNLESS THE DRAWING IS CERTIFIED. BD/BGM BALL MOUNT * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN ASSEMBLY HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION. DIMENSION AND ASSEMBLY DRAWING...
Page 21
UNLESS THE DRAWING IS CERTIFIED. BD/BGM FIXED MOUNTING * ALL EQUIPMENT DESIGN AND APPLICATION DATA SHOWN ASSEMBLY HEREIN IS CONFIDENTIAL AND THE PROPERTIY OF BRAWN MIXER, INC. NO USE OR DISCLOSURE THEREOF MAY BE MADE WITHOUT OUR WRITTEN PERMISSION. DIMENSION AND ASSEMBLY DRAWING...
Page 22
500075 $352 38 [BD(F)] Angle riser 500121 $182 O-ring 10028602 NOTES Consult Factory: provide serial number with request for quotation. SPARE PARTS KIT Add $679 Shaded items = Recommended Spare Parts Kit Copyright 2015 BRAWN Mixer, Inc. 06/15/2015 Page 2-2...
Page 23
– THIS PAGE IS INTENTIONALLY LEFT BLANK –...
Page 24
– THIS PAGE IS INTENTIONALLY LEFT BLANK –...
Page 25
– THIS PAGE IS INTENTIONALLY LEFT BLANK –...
Page 26
3389 128 AVE. HOLLAND, MI 49424 BRAWN MIXER SALES REPRESENTATIVES PHONE: 616-399-5600 FAX: 616-399-3084 UNITED STATES ILLINOIS (SOUTHERN) MISSOURI (EASTERN) OKLAHOMA WEST VIRGINIA (EASTERN) MID-STATES ENGINEERED EQUIP. MID-STATES ENGINEERED EQUIP. G.C. SOLUTIONS DATA DESIGN SERVICES 2244 ROSE LANE 2244 ROSE LANE P.O.