Changing The Speaker Setting To Suit Your Speakers - Panasonic DMP-BD10 Operating Instructions Manual

Tabs
HDMI Video Mode
HDMI
Select "On" when video is output from HDMI AV OUT
terminal.
HDMI Resolution
You can only select settings compatible with the connected
equipment. This setting normally does not need to be
changed. However if you are concerned about output picture
quality, it may be improved by changing the setting.
Still pictures play at a resolution equivalent to 480p
regardless of the settings.
HDMI RGB Output Range
Effective when connected to a device that only supports RGB
output.
HDMI Audio Output
This setting selects whether or not to output audio from HDMI.
[Note]:If "On" is selected, audio output from the 7.1ch AUDIO
OUT terminal will match the number of channels on the
equipment connected with HDMI.
Ctrl with HDMI

Changing the speaker setting to suit your speakers

When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on
the amplifier/receiver.
Front (L)
Center
ms
L C
0.0
dB
Complete
0.0
Complete
Test
dB ms
LS
0.0 0.0
Test
dB ms
LB
0.0 0.0
(LS) Surround (RS)
Speaker presence and size ( )
Press [ , , , ] to select the speaker icon ( ) and press
[ENTER].
Press [ , ] to select the setting and press [ENTER].
Icon examples:
Surround speaker (LS)
Large: Select when the
speaker supports
low-frequency (under
100 Hz) reproduction.
Small: Select when the speaker does not support low-frequency
reproduction.
In order to make an ideal listening environment, settings of speaker
sizes may be automatically adjusted.
For example, if the subwoofer is set to "No", the front speakers will
automatically be set to "Large". (In this case, we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
Delay time ( )
(Effective when playing multi-channel audio)
(Center, surround and surround back speakers only)
For optimum listening with 7.1/5.1-channel sound, all the speakers,
except for the subwoofer, should be the same distance from the
seating position.
If you have to place the center, surround and surround back speakers
closer to the seating position, adjust the delay time to make up for the
difference.
If either distance or is less than
relevant table and change to the recommended setting.
Press [ , , , ] to select the delay time box ( ) and press
[ENTER].
Press [ , ] to select the setting and press [ENTER].
Menus
Front (R)
dB
R
0.0
dB
0.0
Subwoofer
dB
SW
0.0
dB
RS
0.0
dB
RB
0.0
(LB) Surround back
(RB)
LS LS
Large Small No
, find the difference in the
Settings
Options (Underlined items are the factory presets.)
On: [Note]:Video from COMPONENT VIDEO OUT
terminal is output as "480i" if this is selected.
Off
Auto: Automatically selects the output resolution
best suited to the connected television
(1080p, 1080i, 720p or 480p).
480p
720p
1080i
1080p
Standard:
Enhanced: When the black and white images are not
distinct.
On:
Off: When the TV is connected to this unit with an
HDMI cable, and you are connected to an
amplifier/receiver that does not support HDMI.
On: When "On" is selected, you can operate other
EZ Sync HDAVI control compatible devices (➡ 18).
Off:
5.1ch speaker connection
Approximate room dimensions
C
C
L R
SW
LS
RS
LS RS
Circle of constant primary listening distance
: Actual speaker position
: Ideal speaker position
Center speaker
Difference
Approx. 34 cm (1 1 10 feet)
Approx. 68 cm (2 1 5 feet)
3 10
Approx. 102 cm (3 feet)
2 5
Approx. 136 cm (4 feet)
Approx. 170 cm (5 1 feet)
2
Surround/Surround back speakers
Difference
Approx. 170 cm (5 1 2 feet)
Approx. 340 cm (11 feet)
Approx. 510 cm (16 1 feet)
2
Channel balance ( )
(Effective when playing multi-channel audio)
This does not work when connected with HDMI terminals and "HDMI
Audio Output" (➜ above, "HDMI" tab) is set to "On".
Select "Test" and press [ENTER].
A test signal is output.
Front (L) Center Front (R)
Surround (LS) Surround Back(LB)
While listening to the test signal, press [
of each speaker
Front speakers: 0.0 to 6.0 dB
Except for front speakers: 0.0 to
Press [ENTER]. .
The test signal stops.
No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
To finish the speaker setting
Press [ ] to select "Complete" and press [ENTER].
Changing the unit's settings
7.1ch speaker connection
C
L C
R
SW
LS RS
LS RS
LB
RB
LB RB
: Primary listening
distance
Setting
1.0 ms
2.0 ms
3.0 ms
4.0 ms
5.0 ms
Setting
5.0 ms
10.0 ms
15.0 ms
Surround (RS)
Surround Back (RB)
] to adjust the volume
12.0 dB
RQT8745
23