Download Print this page

BITMAIN AntMiner S7 Manual

Hide thumbs

Advertisement

BITMAIN
AntMiner S7 Manual

Advertisement

loading

  Also See for BITMAIN AntMiner S7

  Summary of Contents for BITMAIN AntMiner S7

  • Page 1 BITMAIN AntMiner S7 Manual...
  • Page 2: Table Of Contents

    AntMiner Manual Last updated: 2/1/2016 Page 2 of 11 Contents Overview ........................... 3 Features ............................. 4 Power Supply..........................4 Connect to Miner ........................6 Miner Configuration ........................8 Pool Setting ........................8 Frequency Modification ....................8 Miner Status ..........................9 System Configuration and status ....................
  • Page 3: Overview

    Page 3 of 11 1 Overview The AntMiner S7 with is Bitmain’s newest iteration, using the new state of the art BM1385 chip with full-customs made, powered by ultra-low power 28nm technology. It’s with several different hash rate and the final one is 4.73th/s. S7 are tested and configured prior to shipping to make it easier for customers to set up.
  • Page 4: Features

    Higher input voltage will cause higher mining efficiency. 3 Power Supply Each AntMiner S7 has 9 PCI-e connectors for +12V/15A DC STABLE input on hash boards and 1 PCI-e connector on the controller, all the 10 PCI-e connectors are required. Do not connect more than one PSU to the same hashing board to prevent possible damage and instability.
  • Page 5 AntMiner Manual Last updated: 2/1/2016 Page 5 of 11 Page 5 / 11...
  • Page 6: Connect To Miner

    AntMiner Manual Last updated: 2/1/2016 Page 6 of 11 4 Connect to Miner Step 1. The default DHCP network protocol distributes IP addresses automatically. Please download IPReporter.zip from minerlink.com, then please follow below steps to find out the IP of the miner.
  • Page 7 AntMiner Manual Last updated: 2/1/2016 Page 7 of 11 Step 2. Enter the IP address provided into your WEB browser and proceed to login using ‘root’ for both the username and password. In the ‘Network’ section, you can assign a ‘Static’ IP address if you like. Click ‘Save&Apply’ after modifying it.
  • Page 8: Miner Configuration

    Password- This is the password for your selected worker. Comment: 4.1.1 The AntMiner S7 can be set up with three mining pools, with decreasing priority from the first pool (pool 1) to the third pool (pool 3). The pools with low priority will only be used if all higher priority pools have gone offline.
  • Page 9: Miner Status

    AntMiner Manual Last updated: 2/1/2016 Page 9 of 11 6 Miner Status You can check the operating status of your miner on ‘Miner Status’ page. ASIC#: Number of chips detected in the chain Frequency: ASIC frequency setting Temp: Temperature, centigrade ASIC status: o stands for OK, x stands for error.
  • Page 10: Password Modification

    AntMiner Manual Last updated: 2/1/2016 Page 10 of 11 ‘Keep setting’ is chosen by default and should be enabled if you want to keep your current settings. You should deselect this option if you are trying to return the miner to default settings. Click ‘Browse’...
  • Page 11: Software Version Checking

    AntMiner Manual Last updated: 2/1/2016 Page 11 of 11 7.3 Software Version Checking You can check which version of the software you are currently running on the ‘System->Overview’ page. ‘File System version’ displays the date of the firmware your miner use. In the example below, the miner is using 20150915 firmware.